Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
1. Slave address is not reflected in the address register of TWI0.
2. other information is reflected in registers like operating frequency, SDA, SCL as well as enable. ...
Problem: While connecting with smartphone to several devices based on nrf52832, works only last connected device. Smartphone Application uses Nordic Android library (no.nordicsemi...
I'm using a TI Launchpad , together with the nRF Connect application on my Samsung Galaxy S21. I've got the launchpad connected to my computer and I'm using TI's bTool to...
Hi Nordic
After fellow your youtube tutorials, blinky sample can be built successfully. Flashing code to PCA10090 DK,
the LED started blinky well.
However, it failed...
I have a BLE application (Bluetooth peripheral app) using Zephyr with nRF Connect SDK v1.5.1 and Segger Embedded Studio. I was successful in adding/configuring the MCU Boot...
Hi All,
I'm getting this message everytime I open power profiler, previously working with PPK2, reloading doesn't resolve. Cancelling results in enumeration of PPK2 as unknown...
Hello Everyone,
I'm developing an application which makes use of UART in open thread sdk.
Now, libopenthread-nrf52840-sdk.a library already makes use of UART0, when I...
Hello!
I am trying to sample a digital signal with 12-bits (In a later stage I will need to sample two 12-bits signals). At the moment I am storing the recorded signal...
Hello Nordic team,
I am faced with the problem of developing a custom bootloader which actively pulls FW from an external mass-storage. AFAIK, the SDK only supports OTA...
Hi,
We are using SDK 14.2 with s132 v5.1.0. Reviewing the changelog for newer versions of the SoftDevice, we see:
"Fixed an issue where the application might not receive...
Hi guys,
I am trying to get the PWM rocking. Everything works, but as soon as I define a nrfx_pwm_handler_t in the nrfx_pwm_init, my system crashes with the following error...
Hello Nordic Team,
We are developing a wearable device. We noticed spontaneous BLE disconnections every 1-2 hours. The error code is BLE_HCI_INSTANT_PASSED. I have checked...
We are starting a new wearable device design which will be worn by the user on the chest. We are looking forward to use NRF5340/NRF52840 based modules. The final design is...
hello together,
I would like to use this chip nRF9160-SIAA-B1A-R now only as LTE modem. But the modem should be controlled by two external MCU. Please see figure.
...
Hi support team,
Our purpose is to provide the modules to our customers. We have developped the hardware module based on nrf52832. Now we want to test the BLE mesh functionalities...
