Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Trying to flash firmware to nRF5340 cpuapp core with a sample from nRF connect sdk 1.6.1. I'm able to flash it to a PCA10095 dev kit. With EVM-BT40-V1 from Fanstel, I can...
Hi. I have came into trouble with nrfutil and the provided images.
I have a board that's connected via usb to the computer and I am trying to use the connectivity firmware...
In the nRF5340 user manual section 7.14.3, there is a note regarding assigning the same pin on more than one GPIOTE channel can result in unpredictable behavior. We have implemented...
Hello Jared,
the previous ticket find under the following link is locked. So I decided to open a new one.
https://devzone.nordicsemi.com/f/nordic-q-a/80312/uart-break...
Hi Nordic,
A important customer employ nRF5340 in their product, they are chosing the 32M crystal osciallor now.
Form the SPEC of 5340, if we want to communicate with...
I posted this theme, but the post is locked before fixed. I don't know the reason so repost. I'm sorry about this case.
-------------------------
Question:
I consider...
Hi,
I have a custom board with nrf52840 chipset that controls a GSM modem over UART, and this setup works just fine (zephyr project).
Now, I'm trying to replicate this...
Hi everybody,
I get this error trying to set coded_phy advertising on nrf52840 dongle. This is the code that i try.
The error that i get is:
That means I/O error...
I flash v1.7.0 at_client and mfw-v1.3.0 into nrf9160-DK board, LTE works normally and the board can get the ip. ( https://files.slack.com/files-pri/T0SBEQ7AR-F02J4REC8RX/nordic...
I'm trying to implement communication protocol that involves clock and bidirectional I/O line. Clock signal is coming from an external device and expected to be in 1-5MHz...
Hi,
Could you please help to fill which nRF9160 SIP revision fit for SDK?
nRF9160 modem firmware version
nRF Connect SDK
nRF9160-DK, SIP revision (BA, B0,...
Hello,
I have a question about the best way of implementation.
The data will consists out of a struct with multiple pressure and temperature measurements coming from another...
Hi everyone,
I have this question to ask. So I am trying do make an end device that run on low power. I can see that there is an example about the sleepy end device in the...
