Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi everyone. I just bought the nrf52832 Develop Kit. However, after trying to flash write the sample, my nrf52832 Develop Kit doesn't work and won't flash write the next time...
Hi, I'm using BC805M module which uses nRF52805 SoC.
I have a power ON/OFF button on the PCB. If I press the button (deep sleep mode) during BLE connection, the BLE will...
Hi, I'm using nRF52805.
In my code, I used BLE to transmit I2C and ADC data to the mobile app nRF Connect correctly and continuously.
I tried to use NRF_LOG_INFO() and...
Hi. I am working on firmware for nRF9160 based IoT device Already found a way how I can switch between two different images in flash from the current firmware and it's super...
Hi,
I'm trying to achieve a higher transmission speed between nRF9160 and PC on Thingy91 using connectivity_bridge from NCS 1.7.0. On the 115200 everything is working fine...
Hi,
I am trying to flash one nrf52-DK using the other nrf52-DK.I am using nrfconnect App to flash on Linux.
I am getting an error as:
ERROR Could not fetch memory...
Dear Nordic
I want to set different NUS_BASE_UUID for server and character, as below,
how to set below three NUS_BASE_UUID to different valve.
服务: 49535343-FE7D-4AE5...
Hi
I am using nRF52832 and SDK13 versions.
Can I change the bootloader start address from 0x78000 to 0x77000?
Currently, bootloaders are using 0x78000 to 0x7DFFF area...
Hi all, As written above, as soon as I try to send an array of 8 bytes(8,255,0,1,64,64,0,1) onto the NUS the ble_nus_data_send and the consecutive sd_ble_gatts_hvx() trigger...
Hello,
According to below thread, we could choice 16MHz external crystal with minimal “startup” current consumption:
https://devzone.nordicsemi.com/f/nordic-q-a/1657...
Hello all,
I am trying to compile the Light Switch sample here https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/mesh/light_switch/README...
I have an application and a bootloader, both using the cc310 backend.
In my bootloader code, I find that nrf_crypto_rng_init fails, because CRYS_RndInit returns CRYS_RND_INSTANTIATION_ERROR...
Hello,
I am trying to build the default main.c code for Hello World for nrf5340 using the SEGGER IDE , through "Open nrfConnect SDK Project".
The SEGGER IDE version is...
