I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I m using nRF52840 dongle to setup the nRF5_SDK_17.0.2 .
Besides, the related software and the Segger Embedded Studio are installed.
Occurred Problems :
When...
Dear members,
How can I wake up the system after idle ?
It goes to main loop, but never wakes up if there's a signal from HRM,BSC or B.Power after search time out and...
Dear everyone.
Sorry for my cheep question.
We are using nRF51822 as Bluetooth4.1 with Softdevice S120 and S110 .
Is this device affected by the "BrakTooth" attack?...
Hello,
I am currently working on a project that requires to sample a 50Hz sine wave and transmit the data point over BLE, which will need around 10 - 20 samples per cycle...
Hi There
I’m hoping to implement a low power always-on/listening (response time <10s) industrial product in the UK
I’ve spoken to several acquaintances and had conflicting...
Hi All:
We are using nRF52840 SDK with BLE Mesh sdk5.0 to develop bluetooth mesh and we can use light_sw_client to control the LED1 state on the light_sw_sever via BLE Mesh...
I am using PC code derived from pc-ble-driver heart rate collector with a nRF52840 dev board
On adding characteristics sd_ble_uuid_vs_add() I get an error of 4 - NRF_ERROR_NO_MEM...
I have an nrf52832 acting as a central device that is trying to connect to a peripheral. However, after the peripheral disconnects and the central tries to reconnect I get...
Hi,
I was looking at this page https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_modifying.html and saw the following line:
"When building your application...
I am getting an NRF_ERROR_CRYPTO_RNG_INIT_FAILED from nrf_crypto_rng_backend_init during the sm_init sequence. Any suggestions on what might be causing this?
Hi Sir/Madam,
Our project needs to use TEE on nRF5340 which seems to be implemented by TF-M for now and future. After investigating the implementation, I didn't find a...
Greetings,
What is the minimum low pulse required to externally reset the nRF5340?
I see this answer for nRF51 and this answer for nRF52 . Can I assume nRF53 will be the...
Hi,
I have a nRF9160 DK and Iam trying to join my Private NB-IoT network that my company has (So I can get a static IP). I have the NB-IoT activated Nano SIM and the credentials...
