Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi Nordic DevTeam,
I am using nRF52840 (1MB Flash, 256kB RAM). I would like to store a log data to flash memory that I can extract them to my Android phone later on when...
Hi All,
I want to verfiy the current consumption of nRF52840. I'm using an nRF52840 DK and SDK 17.0.2 RTC example. below are the verfiy steps:
1. Cut SB40 on PCA10056...
Hi,
I we are developing project on BLE NRF52832 module and it warked correctly. during the debugging suddnely it stoped responging to programmer and couldn't be reprogrammed...
I have read about eddystone protocol. I have run
nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_eddystone\pca10040\s132\arm5_no_packs
i am able to build the code...
Hello
My setup looks like this. I am using nrf5_SDK_for_Mesh_v5.0.0 with nRF5_SDK_17.0.2. I have extended the sensor model example (in nrf5_SDK_for_Mesh_v5.0.0) and call...
Just wanted to get clarity on the usage of RACP. In the Glucose SDK example, every measurement gets saved to the database regardless if a Central is connected or not. Why...
Hi,
[246] System: Intermittent extra current consumption when going to sleep
This anomaly applies to IC Rev. Revision 2, build codes CKAA-Dx0, QIAA-Dx0.
It was inherited...
Hello everyone,
I am new and tried some example on the nrf52840 devkit and dongle, including light switch example.
I am now going to send some ASCII bytes through the...
Hi,
The nrf52840 is mounted in our custom board. We found a Jlink programmer , hoping that this programmer is compatible with our chip(nrf52840) to flash the program onto...
Hello! As the subject implies, I'm looking for a Zephyr BLE Long Range Advertiser Example for the nRF52840 DK. Can anyone point me in the direction of one (if it exists)?...
Hi,
I can use nrf21540 to enhance TX power and can see it result, it work fine (The value RSSI in nrfConnect app increase by about 20dbm)
Now, I want to combine both Tx...
Hi, I am working on the mesh serial and run that successfully once using sdk5 for mesh V.5 and nrf52840 devkit and an nrf52840 dongle as a server node. I have several questions...
I am looking into a project that uses a Bluetooth mic and Bluetooth speakers paired to the same computer at the same time. I'm familiar with Bluetooth and with Nordic's offerings...
