Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi,
My journey for upgrading from SDK 1.3 to 1.4 continues. Now I have hints about how to not make random number generation to crash devzone.nordicsemi.com/.../nrf9160-sdk...
Hi Dear
Good Day!!
I want to know about which clock frequency they are used in nrf5SDK internal or external FREQ, and along with the where can i find the declarations...
Hello,
I am trying to work on an application to transfer BLE characteristic data to an SD card.
I ran the FATFS example on my setup and it works perfectly with the Test...
Dear sir.
I'm an engineering working on circuit design , micom program, and PCB artwork. from korea. My name is Jeong eui-jong.([email protected])
In conclusion,...
Dear Nordic Team,
I am currently using nRF52840 with nRF5 SDK v16.0.0 for developing a prototype of wearable device.
The wearable device should be able to act as
a)...
I'm implementing the full modem firmware update as demonstrated by the sample located at /samples/nrf9160/http_update/full_modem_update.
A bunch of it works. I'm able to...
I try to modify one of the pc-ble-driver examples to work together with my PCA10040 and the Nordic UART Service example in my Qt application, but the application doesn´t discover...
Hello,
I'm currently using SDK v17.0.2 with the NRF52840 on nRF52840-DK Board. After going through the example code of "nrfx_spim" I was able to get up and running. I...
Hi, I am trying to integrate DWS3000 (UWB) APIs, given here to nRF52840 with BLE stack enabled such that my firmware can blink Eddystone packets at the same time when UWB...
The customer requested that pairing be prohibited under certain circumstances, so I called API
sd_ble_gap_sec_params_reply(m_conn_handle, BLE_GAP_SEC_STATUS_PAIRING_NOT_SUPP...
in ~/ncs/zephyr/samples/hello_world/prj.conf or in ~/ncs/zephyr/boards/arm/nrf9160dk_nrf9160/nrf9160dk_nrf9160ns_defconfig
CONFIG_I2C=y
in my nrf9160dk_nrf9160ns.overlay...
Hi,
We are using nrf52833 for measuring angle of arrival. We got IQ samples from the device we need to calculate the phase difference from that IQ sample. please explain...
Hi, we have an application using an nRF52832 without a SD that we want to put into low power / sleep mode to save battery.
What commands should we use to do this and wake...
