Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Using: NRF52840, SDK 14.2, S140
My GPIO initialization code is as follows. This is the first thing that happens in main.c.
Here are logic analyzer traces of 2 GPIOs...
Hi
We would like to adjust the pin matching of our nRF52805 design since the measured S11 coefficients in Tx mode are not very good (well above -3dB). The values for the...
Hi.
I am testing a wearable device based on nRF52832 and it does not have a reboot button.
Sometimes the device gets stuck and does not appear on Bluetooth scans. Rebooting...
Hello, I'm in Zephyr OS build v2.3.0 and NCS v1.3.0. I need to reprogram UART0 baudrate at run time to 38400. After having obtained the uart node
uart = device_get_binding...
I want to transmit UART and Bluetooth through 12bit ADC 12k sampling.
I downloaded the following example and verified the ADC-UART AND Bluetooth communication. https://github...
Hi,
I use the nRF52840 chip, which is designed as a module.
I use nRF9160 DK to burn the hex file.
1.And i can use nRF connect to read the ic of the module.
But...
Hi there, We're using SDK 16.0.0_98a98e2. Our setup is a PC running BLE Central connecting to 2 nRF 52840 running as BLE peripherals. We use the provided BLE UART example...
Dir Sir or Madam,
I defined 2 properties in sensor_server mesh example,
Precise Present Ambient Temperature (0x0075) and Present Indoor Relative Humidity (0x00A7) ,
...
Hi,
I use sd system power off to go into sleep mode. I wake up with the help of a button. However, the 1 second wake up time is too much for us. Do we have a chance to set...
I am currently trying to send indefinitely large files over BLE. To do this I have a central and peripheral application running between 2 nRF52840's (one peripheral, one central...
Hi,
NRF52832, SD S132 7.0.1, SDK16, custom device, custom SW
The: custom device not bonded.
In my firmware I can run beaconing in parallel with connectivity advertisement...
Hi sir,
I encountered a problem while building Thingy SDK using segger. Here are steps what I did,
Downloaded "thingy_sdk_v2.1.0" SDK from this https://www.nordicsemi...
Hi there,
When I operate SPI and I2C simultaneously on nRF52832, an error has occurred.
Could you please teach me how to solve an error?
I use an attached "main.c"....
