I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
I am attempting to provision the sensor mesh example using the static provisioner example from the MESH SDK.
It works great. However, the client receives two broadcasts...
Hi community,
Starting with a new product on the nRF52, I was playing with the Serial Flash of the nRF52840 DK.
I have been using similar Serial Flash on other platforms...
Hi !
I'm trying to debug. I followed this video : https://www.youtube.com/watch?v=uP8RYgYGRvI&list=PLx_tBuQ_KSqGHmzdEL2GWEOeix-S5rgTV&index=7 . But I can't completely. ...
I would like to use nRF52 DK (nRF52832) to program Fanstel BC805M EK (nRF52805) . When I upload to code from nrf52 DK to BC805M, I got this error message.
I know that...
I have many of these types of systems running in a single room but when I try to run more than 8 I start start to get errors. How many systems should be able to run in the...
I am creating a saadc project based on the ble_app_uart project.
The source code is as follows.
If you download after compiling, the following operation is performed...
Hi, all
I am studying the bsp part while looking at the example of 'ble_app_uart'. (pca10056)
The difference between 'bsp_event_handler' and 'bsp_button_event_handler...
Hi DevZone,
I want to perform USB bulk transmits to a host device while using the app_usbd library. I am using SDK 15.3 and the s140 soft device is enabled.
I have found...
Hello Nordic Team;
The Vdd value range for the nRF9160 is 3.00 V to 5.5 V. We will use li-PO battery in our system. Can I power the nRF9160 directly from the battery without...
Hi,
I am using Nordic thingy 52 for my application, Now I need to blink LED for 5 seconds on Board when ever a condition is satisfied. But in schematic of Nordic thingy...
Board: nRF51-DK (nRF51422 chip)
SDK: 12.3.0
SoftDevice: S130
Compilation settings
Optimization level O1
Debug information generated
I have seen lot of...
Hi.
I am going to make my own PCB with nrf52832.
Before making it, I have to check debugging through P20 in nrf52832 DK.
I have two nrf52832 DKs with SDK17.0.0....
Platform: nRF5340-DK
Tools: I am using SDK 1.5.0 (but seen on earlier SDKs too)
Configuration: Using high speed spi pins whether for SPI1 or SPI4
If I use SPI1 I see...
Hey guys i wanted to ask you for help on IOS BLE i am currently seeing that nRF Connect seems to work fine over BLE Connection with some devices on Android and as far as i...
