I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi!
I'm trying to do the TCP example with the nRF5_SDK_16.0.0_98a08e2, a nrf52840 DK board and a Raspberry Pi 3 B+ as a gateway but I got some problems.
For connecting...
Hi, I'm testing the ICMP example, using a Raspberry and a custom board with a nRF52840. I follow the instructions on the "Connecting devices to the router" found in the infocenter...
hello,
i am using two customised nrf52840 boards and this example https://github.com/NordicPlayground/nRF52-ble-long-range-demo to get the maximum range between two boards...
Hi.
I have NRF52840 with softdevice and GPIO0.7 and 0.27 connected to DALI CLICK and set up and 0.7 - IN, 0.27 OUT. I'm also using TIMER2 for running callback every 104us...
I'm using nRF52832 with an external motion co-processor. As a part of a robust reset strategy, I want to connect a single nRF52 pin to the co-processor's nRST pin to generate...
Hi
I'm using NCS 1.4.0 and SES. If I change the setting in Serial LTE modem to CONFIG_SLM_CONNECT_UART_2 for external MCU connection, I get an error msg from SES: Cannot...
Hello,
I am using "nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730" for NCP as well as other thread devices. nrfutil version: 5.2.0 RPI3 image: RaspPi_OT_Border_Router_Demo_v3...
I'm running OpenThread on a nrf52840-mdk from maker diary. I'm using the nRF SDK for thread and zigbee.
I would like to poll a sensor periodically. OpenThread does not offer...
hi support team,
i found that 52833 UART power is different from 832,
in SDK17.0.2,
832 is still 1.15 mA(with DMA), however 833 is about 0.437 mA(with DMA),
832 is...
Hello,
I want to use the BLE UART example on my PCA10040 development board, but I can´t transmit or receive any data from my PC to the smartphone with the nRF Connect app...
Hi all,
I have a question.
When I try send message coap, it can send as mesh network.
But when I send search gateway msg, connect msg from publish (subscribe) Node to...
My custom nRF9160 board does not communicate with nRF Connect Programmer.
"Unsupported device. The detected device could not be recognized as neither JLink device nor Nordic...
Hello everyone!
I have some issue with the comparator module on the nrf52820 chip.
We need to compare one of external analog signal the 1.8V internal reference source...
Hi,
I try to achieve high throughput via BLE connection between two nRF82540dk boards. I would like to maximize duty cycle of transmission in the connection interval. Unfortunately...
I am sending 240-byte data from peripheral to central through notification (without response) by using the ble_nus_data_send() function when the BLE_NUS_EVT_TX_RDY event comes...
