I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
My company produces smart helmets and our products have always been using nRF5 v11 SDK on nRF52 chips for almost 5 years now. The latest nRF5 SDK is already on v17 https:...
Hello there,
I am trying to send an add_group_request to a device on the network, and want to capture the send status of the device to check the status of the call. I am...
Hello,
I have been testing out the Power Profiler Kit on an nrf52840 DK (board revision 1.1.0) with the blinky example (SDK 3.2). All is working well and I am able to plot...
Hi Team, Using the nrfconnect for mobile application. Where it is connecting to the BLE device. As every time connecting the MAC address of the mobile is changing, I know...
Dear Sir / Ma'am ,
I am trying to load my simple I2C program on board nrf52840dk. But unfortunately after some time on board LED5 can't turned on and COM PORT not detected...
Hi,
I use nrf52832 with SO 6.0.0 and SDK 15 connected with and IOS 14.2 (iphone XSmax)
some time (about 1 time on 400 connection) in the first packets exchanged after...
Hi ,
I'm working on nrf52833, s113.
I have trouble to secure my system. It has no kayboard or screen, and with 6digit fixd pathkey( no other choice).
That's mean it...
hi there, I have a problem with updating the firmware when the PPK is attached to the nRF52 DK.
I could upload a new version of firmware on the nrf52, but it loads the previous...
Hi,
I've 10 nRF52832 running as peripheral and connects to a single central node (like star topology) and I need to perform the DFU by OTA for all the peripheral devices...
Hello all,
Please help!
I am using nrf52480 with SDK15.
I have been developing this application for quite some time now and this is a new problem. I am using BLE_GATTS_EVT_RW_AUTHORIZE_REQUESTs...
We used the NRF52840 in our product. I want to experiment with Long Range BLE using PHY Coded. I will be using:
-Peripheral - The Product
-Master NRF52840 DK
Are there...
There have been several tickets raised on this subject.
Yesterday I installed the latest sdk, v1.4.99-dev1, on a clean windows 10 installation, with nanopb 0.4.2 and still...
hi
Quick question
I read the post here , it stated the nRF51822 device ID is random generated (FIPS compliant)
How are the DEVICEID, DEVICEADDR, ER, & IR values set...
