Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi everyone,
I am making a project to dim a led strip following PWM driver example, everything works pretty well but i only have one problem that I need to set a state for...
Hi,
I'm trying to debug my application using monitor mode debugging and after setting a breakpoint while the code is running I usually have an assertion that fails in the...
Hi,
I have downloaded the nrf5 Sdk 17.02 and nrf mesh 5.0.
Kit:nrf52832
Ide:segger ide
1. Can you please tell me how the data gets transferred and stored in ble stack...
Hi!We used a 52832 to make a bracelet. Now some apps on Huawei phones can't be remotely upgraded by the ring. We have verified that Nordic's official Android DFU library throws...
Dear Sir,
I'm testing the Rx sensitivity of EVB (nrf52840-DK).
I use PER 30% be the thresholde and get Rx sensitivity; -92 dBm/ 1M , -88dBm/2M.
It's different with datasheet...
Hi Nordic,
I have upgraded my NCS folder to version to v1.4.2 and couldnt able to open SLM application(v1.4.2\nrf\applications\serial_lte_modem).
I am receiving below...
Hi,
probably very basic question. I found some nrf code in nordic sdk. I don't remember the version of SDK. I compiled and deployed it on nrf52840 devkit and also on dongle...
The issue:
1) Program x2 NRF52840 dev boards
2) comment board A to windows, windows reports COM n
3) unplug board A and connect board B
4) windows reports the same...
Hello Everyone,
We are using nRF52840 IC for our products which has 1 MB of flash.
Thread Secure DFU Example provided with Nordic SDK supports only Dual Bank DFU. This...
hi,
we have an product using 51422 for many years, now customer ask support dual bel connection, please help confirm if it is possible? which sdk version and if there...
The chip we use is nrf52832 and the SDK is nrf5_ SDK_ 15.3.0_ 59ac345, the booeloader uses the example project nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040_ble_debug...
Hello,
I am developing one Zigbee based product for that I am using nRF52840 and light_bulb examples and modified as per my requirement.
Till now everything successfully...
I've just found through some trial and error that SoftDevice (s130 at least) on the nRF51 DK handles a sequence of notifications in the following manner:
call sd_ble_gatts_hvx...
