I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hello,
I would like to program the NRF52840DK to send ZigBee beacon(not beacon request) to the end devices, but I cannot seem to find the API, etc. to do so.
Or perhaps...
Hello NRF ,
I am not able to run any of the the BLE peripheral example codes from the SDK12.2.0 ( Nordic NRF 52 SDK ) .
The reason I am using 12.2.0 is I have a sensor...
Hi,
I need a battery calculation in my project, For that I need to implement ADC.
But in SDK17 their is no ADC sample example for nrf52810 is present. So please suggest...
Hi Team,
I have nrf52840 DK board and is trying to get the prints from nRF USB port using cdc_acm application. I can see the prints when I connect the DK board with the...
Hello, I am trying to set the company ID and manufacturer specific data in the NCS SDK using nRF52840 dev board
I have the following array of structure
uint8_t COMPANY_ID...
Hi,
I am trying to generate unique key(s) for every device and store them in Optiga to sign the messages, among others. After generating the key pairs, I need the private...
Hello. Currently, the Samsung Galaxy A series has a problem that UART communication is not available.
I want to find the cause and solution of this problem, How can I find...
I am using nrf52852 with sdk 16 version and I want to set the BLE connection interval via BLE command using an customised app. what i want to do is this
#define MIN_CONN_INTERVAL...
HI, I'm developing a device (based on uBlox Anna-B112 with nRF52832) that must securely store three 256bit keys. These keys must remain secret and must not be readable by...
Hi,
I'm just starting out with zephyr on a nrf52dk (nrf52832) and I'm in need of performing some math functions on the data output on a mpu6050.
The MPU6050 is spitting...
We are developing couple of products based on nordic 52810 and 52820. Mainly 52810 And we have received very good support from nordic team and very promp and pro-active support...
The documentation is unclear about QSPI handling:
If I issue a QSPI erase command then I receive confirmation that the erase command has been written to the external QSPI...
I'm using FDS module from nRF SDK 16.0.0.
Below I'll describe issue which I'm experiencing when trying to initialize FDS twice:
To be sure that my FDS filesystem will...
Was going through the process of updating the modem and application on my just purchased Thingy-91. Initially the programmer reported that the processor and two serial ports...
Hi,
I am getting this error with the new EVK 0.15.0 2020.42.
Any thoughts on what I need to do?
Thanks, David
%CESQ: 255,0,255,0
+CEREG: 2,"FFFE","FFFFFFFF"...
