Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
I want to use external power (battery) and USB power together.
If USB is not connected, I want to supply it with battery power, and if USB is connected, I want to...
Dear HW engineer,
I have ordered a few custom boards with nRF52820. As recommended by the datasheet, I have used 12pF load capacitors for both HF (32MHz) and LF (32kHz)...
Hello
I use nrf52832 and SDK v17.
I'm conducting various tests on Bluetooth. And I faced a lot of new problems. I erased a previously saved bond from the Android nrf connect...
Hi
After successfully testing nRF9160 SLM app. we plan to use nRF9160 with UDP and LwM2M protocol in our smart devices. We also have our private cloud server where all the...
Im new using Nordic devices , I am trying to using nrf52840DK to locate nrf52840 dongles using the direction finding method , how can I connect the dongles to the DK and build...
HI,
Is it possible to update modem firmware from 1.2.0 straight to 1.2.2? Or is it the only way to first update from 1.2.0 to 1.2.1 and then to 1.2.2?
Regards, Tero
Hello
I'm testing the firmware using the BLE. When I upload, I can see that the board is working. Also, I don't think there's a problem with running each line of debugger...
I'm trying to build the blinky zephyr sample for nRF Connect SDK and get the following failure:
Creating solution blinky.emProject
/usr/local/bin/cmake -GNinja -DBOARD...
How can I, from the pc-ble-driver API, send an insufficient authentication request without configuring a characteristic to be secured?
I am testing out new standards. One...
Hello, Nordic community,
I want to implement OTA using Thread with nRF Connect SDK.
Is there any sample code or reference this can be done with Thread?
Thanks,
...
Is there a limit to the number of handlers that can be registered using NRF_PWR_MGMT_HANDLER_REGISTER? I can't seem to get any more than 3 to be called, changing NRF_PWR_MGMT_CONFIG_HANDLER_PRIORITY_COUNT...
Hi--I'm part of a research group that will be using the Thingy 52 to record environmental variables, and we will need to transfer information to a cloud server using a satellite...
HI，ALL：
How to setup TX mode in example PRX，and so,how to setup Rx mode in PTX example. I use esb_init() of example PTX in example PRX， But when I fill data in fifo, it...
HI，ALL：
when using ESB example ,the transsmit waveform is below(in channel 3):
how to make it more simple,like that as below(other example in channel 3):
