Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Dear all,
In our project we are using "nrf52840" IC is used. We need to check its strength in various physical layer by loading the " Direct mode code ".
We have sucessfully...
Hi !
I need to develop a BLE communication link between a smartphone (Android first, iOS after) and the BL654 Laird platform (based on nRF52840).
I found multiples strategies...
i am developing a bike power meter and designed my own hardware.
From software point of view I used the Ant+ bikepowermeter example from Nordic.
So far my status is, ...
To the kind attention of Nordic support team,
Could you please help me finding documentation about the subject I mentioned?
Let's suppose we have got a peripheral and...
Hello,
I am working on ble_app_uart example on nRF52840DK.
I am using one switch (gpio) for advertising_switch() function. It means on changing the position of the switch...
Hi,
Would you please tell me how can I dump a memory and save into a file in keil uVersion 5.24?
For example: I want to read the flash memory 0x00000000 to 0x00010000...
There is an option to 'Clone device's services':
A message pops up briefly to say that it's done it:
But it doesn't say where it's put it, and I can't see any...
Dear all,
I have picked the Ruuvi project : https://github.com/ruuvi/ruuvi.firmware.c and change the configuration to adapt with nordic dongle.
But after flashing, my...
Hi,
I am evaluating LC example, I am using an occupancy sensor. So whenever there's an occupancy it's detecting and turning the lights ON. But even when there's occupancy...
Hi,
I have created an eclipse based makefile project for nrf51802 module.
The sdk version that i am using is 12.3.0, and softdevice S130 .
Taking reference of ble_app_uart...
HW setup is my boart connected to a windows10 PC with an uart link.
I tried secure_bootloader_pca10100_uart_ses_nRF5SDKThreadv4.1.0.zip example, with some modification for...
Hi All,
I followed this article and got eclipse to work. I can use debugger, single-step, place a breakpoint. All good.
I noticed that disassembly window shows opcodes...
Hello,
I am working on a project that uses Azure as a cloud IoT provider and the NRF9160 as a gateway-like device which is supposed to make simultaneous connections to up...
Hi,
Just wondering if it is possible to configure the UICR Customer registers after erasing and flashing/programming the nrf52832. The hex file used to program the device...
Hi Team,
I wonder the operating system which has been ported on nRF52840 DK, I found multiple IoT OS what nRF52840 supports like ARM mbed, Zephyr, Contiki, etc. But can...
