I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi Dev Zone Team,
I had a question regarding the current measurement of Nordic Thingy 91. I am following the steps provided in the Thingy91 documentation.
I have a Joulescope...
Hello.
I am testing saadc function.
When I was connect the saadc pin with ground level, the saadc value represents negative value.
So I am searching the similar problem...
Hi:
I'm coding with the nrf52840 dk sample.
as we know, the gatt operate is notify,read, write, etc.
I have found the event about the write,and notify:
case BLE_GATTS_EVT_WRITE...
<environment> Windows10 ncs v1.3.0 modem fw v1.2.0 DK 0.9.0
I made one-shot agps app by modifying gps sample app. The behavior is this.
- download SUPL data from supl...
Just bought 2 nrf52840 DK's both stopped working
Observation
Was able to program and run SDK examples.
Above working setup not disturbed,so all cables are in order...
Hi, I'm using nrf52 dk and struggling to get low power consumption using multi_sensor_freertos ZigBee example from nrf sdk. Can you provide me some guides on how to optimize...
Hello,
nRFSD5 v16.0, softdevice v.7.0.1, nRF52811
I want to detect power failure/low battery voltage using POF feature of nRF52811 chip. Here is the code I'm using:
...
I am trying to capture audio PDM samples at every 5s interval blocks, but at the time of "pevt->buffer_released" event when i am giving the new buffer to PDM driver it results...
Hello, I am working on the NRF9160DK card. I am using SDK 1.3.0 and the latest modem uploaded: www.nordicsemi.com/.../Download 2020-04-29.
Whether it's with the asset_tracker...
Im following the guidance to upload modem code and application code, downloaded from project page, onto the Thingy:91.
Current state, after following guidance, is: I hold...
Hello,
Currently I have implemented a UART callback using the CONFIG_UART_ASYNC_API setting as follows:
However, all data that I receive is appended constantly, until...
Hi, I want to measure the data transfer speed of BLE. I use the nRF52840 DK with the ble_app_uart example
I created a dummy string of 20 bytes (default length of one packet...
I have a shipping product with S132 2.0.1 with multiple problems with the LFRC clock.
There are seemingly at least 4 errata that apply (77, 132, 146, 192).
Are there...
Hello, I'm trying to compile the LIBUARTE example from SDK 16 but im getting undefined reference errors, this is what I've done so far:
in sdk_config.h defined , (I've...
Hi, I am really confused about the Nordic SDK and way of doing things... I have seen so much conflicting documentation.
I am using SDK_for_Thread_and_Zigbee_v4.1.0 (currently...
