Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hello, I am currently working on a nr52840 s140 Sdk 17.0 (dev kit) and a m using the peripheral/uart example code.
The UART TX & RX works perfectly when connecting to a...
Hi,
Quick questions regarding MAGPIO setup.
We are setting up MAGPIO pins via AT commands for RF switches.
Should the AT sentence for setting up MAGPIO be the same...
For a customer we're trying to see if we can build an IoT solution with nrf9160 to periodically send a status update to the cloud. Unfortunately, the devices are typically...
Hi everyone,
I suppose that this is a simple question but I cannot figure out what I am doing wrong. I am trying to set up an interrupt for a GPIO
I call the createInterrupt...
Hi ,
I am working nrf9160 project. I am facing error while downloading the project.
I followed the ticket - https://devzone.nordicsemi.com/f/nordic-q-a/50422/how-send...
Hello together, I am trying to work with the SEGGER software and would like to test it with a Sample from the nRF Connect SDK.
I've installed it over the Toolchain application...
Hi, I want to transfer 900KB file from mobile to NRF52.
I am using nRF5_SDK_15.3.0_59ac345. - Can you guide me for that? - How BLE receives a bin file from DFU via the NRF...
Hello, Following is my development environment IDE: Segger SDK: 16 SoftDevice: S132 Right now, we are trying to merge the following two examples. - examples/peripheral/nrf5...
I'm looking for a simple demonstration application that can run on the nRF52 Dev board and communicate with the default Thingy52 firmware. My plan is to get this working on...
I'm trying to read the Device Name from address 0x21 on a BQ40Z80 fuel gauge, using my nRF9160 chip, connected via SMBus.
When polling the address space, I nicely get an...
I'm using Ubuntu 20.04, SES 4.52c, SDK 16 nRF52840 DK board.
I'm going to need to use the PWM driver to supply clock pulses to an I2S microphone and the I2S peripheral running...
Hello all, I've run into a weird problem that hopefully someone has a clue. My environment: - PCA10040A, nRF52832 - sdk 17.0 - softdevice s132_nrf52_7.0.1_softdevice.hex ...
Hi:
I have a set of 2x Thingy:91 and 2x Thingy:52
I want to make a setup where the devises work in line over a longer distance. T91-T52-T52-T91 is that possible all working...
