Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I am currently tweaking the Thingy:91 to run a stripped down version of my custom application. I have been able to flash the device with the Thingy:91's sample at_client...
hi,
we're using a Adafruit nrf52832 board for a building a ble keyboard . w're able to pair to two central devices and appear to them as a keyboard , but for example : we...
Hi, we are designing a product that needs LTE connectivity and BLE for local setup.
The nRF9160DK uses an nRF52840 with some links for COEX and comms.
Is there any reason...
Hello,
is there any kind of good practice available about how to generate UDP traffic with the nRF9160DK via NB-IoT for a simple test?
As far as I know the AT client...
Hi
I followed below tutorial with my nrf52840 using SDK 15.3.0
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a...
Here is the software: https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF-Sniffer-for-Bluetooth-LE which notably doesn't support the nRF52 dongle
I also...
SDK15.3
nRF52840
S140 v6.1.1
Q1. I have an RTC compare event connected to a Timer count task over PPI. The Timer is configured in low power counter mode. My question...
Hi, I am strugling to get the power comsumption down to the number I have been reading on this forum. I followed the instruction of the dev kit manual . When measuring the...
Hi, I'm getting regular crashes with my app: SOFTDEVICE: ASSERTION FAILED. Using and NRF52832, SDK 15.3.0, SD 132 6.1.1, and Mesh SDK 3.1.0. With DEBUG defined, I don't really...
I'm trying to interface 2 SPH0645 mics to the nRF52840 DK.
Little did I know when I bought them (the mics) that you need to waste 2 timers + 2 pins + memory space to make...
Hi,
I am trying to measure a signal using the SAADC driver on SDK 13. I have used the example from the nrf52 playground for low power ADC
I have a few questions on best...
Hi,
I have a nRF91 development kit and want to connect P4 to the Segger Jtrace for ETM streaming. In the manual, it stated that a 2×10 pin 1.27 mm pitch surface mount connector...
Hi,
Is there any way to get network time without previously setting it with AT+CCLK?
I would like to implement sort of "fake time" by initialising it with the network...
Hi, I'm struggeling with this stage on the "getting started assistant"
"Clone the nRF Connect SDK"
Is there any step by step video to help me do this, I have probably...
I have one service with multiple characteristics(11). Out of 11 characteristics I have 7 characteristics which have notify as their attributes. So when I select the notification...