Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi all,
My name is Szabolcs Vass. We are developing a project with nRF9160 SiP on our custom board. We want to send some measurements periodically to an MQTT server. After...
I have realized the cutdown function with the examples. But now I want to reflesh the number I have published, which means that I first publish a number, then I want to publish...
Hi,
We are using nrf51422 in our project and SDK we are using is 12.3 and soft device is S130. In our project we need Bluetooth device should be connected to upto 3 devices...
Hi
I did DFU with button, i can enter and load zip pack over nrfToolbox mobile.
I tried butonlessDFU, i copied services "experimental_ble_app_buttonless_dfu" and with...
Hi,
I am evaluating the ble_app_template example with nRF52840 SDK.
I added code to create custom service and custom characteristics in the following link:
https://github...
Hi,
i have to watch my program flow in segger debugging mode, so that i enable
#ifndef NRF_LOG_ENABLED #define NRF_LOG_ENABLED 1 #endif
in sdk_config.h file.
now i...
Hi,
I want to display an image sent over Bluetooth on my screen which uses the driver st7735. So I have an application which can send images, and I receive data in the function...
Hello,
we have a problem on BT certification with nRF52810 chip. Certification lab replied that TCRL-2018-2 which is mandatory.
Does anyone know where I can get the QDID...
Hi,
I just wonder when hvn_tx_queue (the notification queue) in softdevice is emptied? Is it emptied on disconnection if it still has notifications in queue to send?
Hello.
I have nRF51822 and nRF52832 boards.
I can use both to capture BLE frames with Wireshark on Linux, and I test that with RACCOON also to capture traffic in terminal...
I'm using the DFU module from SDK 9.0 - I enter the DFU by writing to the DFU control point. Is there a way to exit the DFU and have it go back to the app?
Have seen many good thread explaining this model. But didn't find any full example code for it for client and server Model.
I have tried light switch demo and working fine...
Hello!
So I have a new nRF52811 board which was designed by someone else, that I need to develop some pretty simple firmware for. Full disclosure, the design is based on...
Hi I am working on nRF 52832 and nrf 52840 dongle. I want UART service to be used in my application and application should allow me to scan peripheral devices with user command...
I am a freshman. And I am doing some research on BTE by nRF52832(PCA10040). I want to get RSSI. Could you please tell me if there is a reference code or project in SDK? Many...
