I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hello,
I would like to evaluate nRF9160 for incoming project.
I have Nordic Thingy:91 with iBasis sim card.
Unfortunately, during configuration it turned out, that...
Hi,
We are using nRF9160 for our application and need to design power supply with battery management IC for it and need to know how much power it will consume with all...
Hi,
I would like to setup my nRF52840-Preview-DK as a central to communicate with a peripheral device via UART over BLE.
Once my peripheral device is connected it writes...
I try to connect NRF9160 dev kit to LTE/NBIOT. But device cannot connect to the LTE/NBIOT network. I am using the at_client example with nRFconnect v3.3.0 LTE link monitor...
I have successfully managed to both provision and configure the simple:_on_of_client.
but i'm having troubles configuring the simple_on_off server. I really have no idea...
Hi folks,
I need of your help. I've developed a new custom board with the nrf52840 CKAA ball assignment and I'm having problems on programming it.
I've developed my...
I am getting errors when initializing the Peer Manager in my code. Here are the items that are unique to my setup:
1) I have a thread which uses fstorage to store a single...
Hi all,
Using the nrf52832 TWI, I am trying to interract with a sensor through I2C.
On the same board, I am successfully able to exchange data with an accelerometer...
Hi Everyone
I have an nRF9160 DK v0.8.2 and I'm running the asset_tracket sample.
I'm from Portugal so iBasis sim card doesn't work here. So I went to Spain and tried...
Hi Guys, trying since some weeks to develop an " simple " Gap advertising with only 2 "service Data" ( battery level and an ID of 4 bytes with an uuid of 128bits with Mbed...
Hello.
I run a project on RTOS base on embOS of Segger. Now I want to add a BLE task base on Nordic BLE peripheral UART. As a standalone project not on RTOS it is run O...
With mesh dfu, whether to upgrade the firmware of many different devices at the same time is supported. Multiple device deployment spaces are adjacent, and simultaneous transmission...
How to fix this error: Installnnnnfgo Studio tips can't find nrfjprog.dll The development environment is: windows 10 Pro 64-bit operating system MDK-ARM Plus Version5.20 nRF...
Hi,
I am in the process of converting a large freertos project from nRF52832/SDK14.2 to nRF52840/SDK16.0
I've managed to convert everything but the buttonless DFU...
I seem to be getting odd behavior of the UARTE0. Actually, this same behavior happens with the standard UART0.
I have a loop that sends a two byte message every 1 second...
