Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello!
Could you show me an USBD configuration example which works fine with Arduino serial monitor? Because Arduino serial monitor froze when i send a string , but when...
In the nRF52832 (Laird BL652 module) I have programmed.
MBR + SoftDevice from 0x0000 0000 Application from 0x0002 6000 ~ 0x0005 927C
Now trying to program additional application...
Hi
Is there any documentation regarding bluetooth in nRF52832 specs sheet or anywhere else? I understand that there are examples provided by SDK. But I want to know in detail...
Hello,
we are running BT certification on product with nRF52840 chip. It seems that TCRL-2018-2 is now mandatory.
Did someone know if the QDID certified TCRL-2018-2 is...
I am not able to program the nRF52840DK by copying over the .hex file generated by my project to the JLINK drive. However I am able to successfully program using Segger directly...
Hi,
We are looking at using the key:value store functionality defined in mesh_config.h. Can you provide some additional detail on
HW and or SW configuration required to...
Hi,
We are trying to develop a system of IMUs for motion tracking using multiple Thingy boards and an nRF52832 board. The Thingy boards are used as IMU sensor nodes and...
Hi, This is M.Irfan. I want to send data (collected by mpu6050 sensor) using Bluetooth in my cellphone and want to save it. Can you help me with some example code of sending...
We noticed issues regarding BLE activities when running our custom bootloader. It seems that we have located the cause but would like to have approval for that behavior. ...
Hi All
I am trying to find some example code which uses easy DMA over UART using nrf528240..
Using sdk version 15.0. The example which is available by default uses the...
Hi,
I recently bought a nRF51 Dongle (PCA10031) and a nRF52840-DK (PCA10056) and I am now trying to use it for BLE sniffing with Wireshark. I am running OS X 10.14.4.
...
I compiled 4.0.0 in the past and the generated libraries were named "pc_ble_driver_shared_sd_api_vX.dll".
Now I compiled 4.1.1 and the libraries are named "nrf-ble-driver...
Dear Nordic:
My nRF82832 codes based on nRF5_SDK_15.2.0_9412b96 and used s132_nrf52_6.1.0. But I find the Bluetooth signal of nRF82832 can’t be scanned by smart phone which...
