Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi
I would like to modulate the positive output of the UART using PWM
I know i can feed the UART and a PWM putput into a AND gate no problem, but im wondering if there...
Is there a ready example to run nRf51822 as a controller to external host via HCI commands over UART or USB?
e.g. I want to interface the Nordic chip with an open source...
I am using softDevice S140 with SDK 14.2.0_17b948a, working with the ble_app_blinky.
I need to be able to connect one peripheral device to multiple central devices (peripheral...
I connected via a USB cable my ppk to my computer. But when I fire up ppk.py, it says "no response from ppk. Check power, debugger connection and make sure the firmware is...
Is there any other way of programming the Nordic Thingy other than using the nrf52 DK? Where to get the programming/debugging port's pinout , I didn't find that in the hardware...
After connect devices status GAP Secure status ...->evt.gap_evt.params.auth_status.auth_status 0x0D In documentation absend this code = 0x0D What is It?
I would like to use 1.3 V System power to supply some external circuit that may need max 10 mA. This voltage is available via pin DEC4.
I expect that you are going to...
Hi There, I'm very new to mesh and have a bit of a learning curve to understand the mesh SDK. A few questions for those in the know....
I have been playing around with the...
hi,
can anyone share sample code for getting accel values from MPU9255.?
I have tried with this ,Iam not getting output.
Chip :nrf52382
Board : nrf52Dk - PCA10040...
Hi
How can i configure NRF_LOG with IAR and J-Link connected via USB to a RAK 813 BreakBoard, i'm testing BLE SCAN Application.
Regards,
Julio César Morales bErmúde
Is there a way to modify the code in the ios nrf beacon app to identify nordic beacons?
I am aware that the manufacturing id must be set to 0x004C in order to be identified...
Hello,
Is it possible to create a GATT service with a 128 bit UUID, where each characteristic has a unique 128 bit UUID of it's own?
Looking at the examples, it seems...
Hello guys,
During implementation of a test set for CryptoCell AES CCM* functionality i'm facing some issue with the CryptoCell.
Encryption works fine without any issue...
Hi,
my application application consist of NUS service, one i2c, one spi and one adc. it consumes around 10-11 mA while its running. its was observed that while only running...
