Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
In the cs_de.c, we have an IQ pair extracted from remote_pct and local_pct. Assuming this code runs on initiator (where the ranging is done), and remote/local stands for reflector...
I tried to use NRF_SOCK_RAW and NRF_IPPROTO_RAW to create socket, but found `modem fault`!
//this is my wrapper
socket_create ( true , AF_INET , SOCK_RAW , IPPROTO_RAW...
Hi, I very much doubt this is a SoftDevice issue but sticking it out there as an Apple dev asked me. Short story is I have users in production using an App connecting to NRF52810...
Hello Nordic Team,
I am using nRF5340 DK as a debugger/programmer to develop firmware for the Fanstel EV-WT02C40C module. My goal is to do i2c communication between Renesas...
Good morning, I have built and flashed the l2-e1 exercise on both the nRF5340DK and the nRF54L15DK. When the nRF54L15DK boots, the following output is displayed in the terminal...
Hi,
I’m working on nRF54LM20A and trying to configure the internal capacitors for the 32.768 kHz crystal (LFXO) using the factory trim values in FICR.
According to the...
Hello, read through the documentation about the SAADC and found the TRIM.LINCALCOEFF[n] register. ADC-linearity is important in the project I'm involved in... Seems that the...
Using nrf connect SDK 2.5.0
The nrf device is an L2CAP CoC server. I am using an RPi 4 to test with. The application is for transferring data through UART to another chip...
Greetings!
We have been using an nRF52840 Development Kit for a while now and have been performing FW updates OTA (between the same 3 FW images, cycling and updating between...
I am still on the learning curve of nRF Cloud (and the nRF9151 in general) and am trying to add A-GPS to a project.
Using nRF Connect SDK and Toolchain 3.1.1, I cannot add...
I am using the nRF Connect for Visual Studio Code Add-In running with the nRF Connect 2.5.0 toolchain and was trying to implement the application versioning on a nRF5340 DK...
Hi,
I am working on a project which uses nRF5 sdk v17.1.0 & mbedtls v 2.2.8.2. Now i ma planning to make some changes in application code and re release it. My question...
There appear to be mistakes in haptics_handler.c it appears to be using outdated functions / includes in NCS 3.2.1:
The corrections that work for me:
Changes made: ...
