I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
I'm getting started with this evaluation kit by working through the user guide and almost made it through the Blinky example before I ran into trouble.
After compiling...
We have some hardware versions of the Nrf51822: build BA, CA.
Is the new S110 v6.0.0 softdevice compatible with these hardware versions?
If it is not compatible, wich...
Hi.
Using 51822 with BLE stack, I was faced with the problem of low transfer rates (5kb) on my android device (phone). It is very slow.
Can work 51822 with standart...
Can I initial like below to generate 2 opposition PWM waves on 2Pins？
/* Configure PPI channel 0 to toggle PWM_OUTPUT_PIN on every Timer 2 COMPARE[0] match. */
NRF_PPI...
Hi All,
Now I'm doing the OTA and I can use the nRF51822 DK and Master Control Pannel to complete the firmware update.I have a idear but I meet some problem.
I use the...
Hi,
Is it possible to update the firmware through usb? i have a nrf51822 evaluation kit, and i also tested the firmware update over ble. Now, i need to update the firmware...
HI Everybody,
I am developing firmware for handling multiple ANT+ Sensors. i am able to collect data from 3 different sensors, but in below scenario am getting channel...
Hi,
This may be a silly question but I'm trying to generate two timed interrupt events using only TIMER0 (the MCU is nrf51822). My code is:
#define TIMEOUT1 3000 ...
I am beginner on this platform. I was hoping for KEIl IDE to aid my development, but since license fee is more, i wanted to try GCC platform. But unable to set it up. In nAN...
Hello,
We are developing an application that has to be able to send the data of a VGA image, and We don't know which of the GATT supported profiles will be the best to...
Hi,
I'm using SDK 4.4.2 and softdevice 5.2.1 to try the HID example. Although it is provided for the nRF6350 kit, I ported (buttons and LEDs) the example to the EV kit...
Hi,
I've been using your nRF51822 with considerable success. I now need to migrate across to an M3 for greater power. I want to keep most of the application code I wrote...
Hi
Thank you for the IOS App "nRF Loader" which was released last week. It works well and offers a lot of possibilities for Nordic developpers. I've one question about...
Hi,
I have just opened my nRF8001 DK. It seems like for the evaluation of the nRF8001, I also need to purchase a nRFgo Motherboard, which is sold separetely.
Where does...
