Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Trying to use a standard delay function to keep and output low for several seconds. It is P0.10 on the 52840 set to Active Low and I do see it transition to a low on the o...
Dear,
I am using both nRF52840 UART (UART0 and UARTE1) on the nRF52840 DK.
The default pin assignement is used, such as
UART0 pins are TX/RX 0.6 & 0.5 and
UARTE1...
Hi NRF team,
I am working on one project. I have used 2 PDM Microphones (MMICT5838-00-012). And I have used Zephyr RTOS for development.
I have used the LC3 encoding and...
Hi,
I'm working on a project using MCUboot, TFM, and a network core app. We use MCUboot with an external flash module for OTA firmware updates.
Recently, we tried upgrading...
Hi,
I am following DevAcademy Lesson 5, HTTP over Wi-Fi (Exercise 2), which involves adding TLS to an HTTP connection.
When I remove CONFIG_WPA_SUPP_CRYPTO_PSA=y , I am...
Using an nRF54L15 here (if that matters) and adding mcuboot via sys build to my project. Couple questions:
- How would one adjust the logger baud rate to something other...
Hello,
I have the nRF5340 DK and I want to program/debug an external SoC. I see that in order to do that I can use the connector P19 to connect to an external board with...
I am using an nrf5340 DK instead of the audio DK. Is BT LE possible with this DK. Is there any difference beween NRF5340 DK and audio DK in terms of microntroller.
Hello,
I’m using VS Code with the nRF Connect extension. When I try to build the “bme68x_iaq” application to upload it later to the Nordic Thingy:53 and read its data, I...
Hi,
I have verified the firmware upgrade and file transfer functionality from a Linux-based device to the customized nrf52840 board using the mcumgr tool.
However, the...
Hello, everyone!
I'm interested to know about the possibility of mixing BLE audio and custom BLE Characteristic in one single nRF5340 application.
For example, we would...
Hi DevZone Community,
My Envriornment
1.9.1 NCS nRF9160DK Current Modem Version : 1.3.2 This question is involving a device which is in production. The issue is, if the...
Hi folks,
Recently picked up a new MacBook (M series) and was excited to try some sample projects on my nrf52840dk.
Unfortunately upon trying to Debug, I get the following...
Hello Nordic team,
I followed the official guide to add a custom sensor cluster to my Matter application. Everything built and flashed successfully, and the application...
hello, i have a weired issue with my sensor communication using spi. the code that used the old SDK works, but the one using the new SDK for some reason doesnt. i need to...
