I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi, since the Nrf5340 has two identical Cortex-M33 cores, I was wondering whether it would be possible to enable the trustzone for both cores, and if yes, how. Thanks.
Hello!
We are working on a custom PCB with nrf54l15 chip on nrf connect sdk version 3.2.0.
The I2C (TWIM) SCL line functions correctly, but the SDA line is not being driven...
I thought I had been extremely careful to _not_ brick the device, but apparently I did.
I created a firmware-dfu.zip file, even with appropriate keys, etc. as below.
...
Hi，
During full-device testing, we observed that two devices encounter the MPSL ASSERT: 1, 1519 error after approximately one hour of operation, which causes the MCU to...
Hi Nordic,
On the NCS3.0.2+NRF54L15 platform, we intend to generate pulse widths by controlling P2.1 and P2.5 through timer+PPI. Originally, we planned to use PPI for operation...
Hello,
I have a problem with a tablet that i was planning on using (Xiaomi Pad Pro), my device (nrf25840 dk) is sending data in packets, 4000bytes per packet and its sending...
Hello,
I am working on a custom product based on the nRF9151. I am currently learning RF testing methodologies and setting up a verification plan.
I have read the HW...
Dear all,
I am trying to build bluetooth hci controller for Home Assistant.
I used official example for create usb bluetooth hci controller here:
~/ncs/v3.2.0/zephyr...
Using the options described in ncs documentation for one image pair updates (i.e. not multi-image DFU) appears to be broken in ncs 3.0 and later for upgrading the network...
Hi all,
I'm working with the nRF54L and encountering persistent SAADC issues after short deep sleep cycles.
Setup:
SAADC is configured in differential mode with oversampling...
Issue
When building the Blinky example for the NRF54LM20A with TFM and CONFIG_DEBUG=y the MCU will assert on boot.
When booting an assert is triggered in workspace/modules...
Hello,
I have been developing on a nRF9151DK v0.9.0 for a few weeks now. So far this board is great! However, I have been running some long duration tests recently and logging...
hello, We have a project that uses sound for distance measurement.
When I upgraded from NCSv3.0.0 to NCSv3.2.1, I encountered a problem where the i2s function stopped working...
Hello, I previously learned that the nRF54L15-DK only supports a single antenna for Bluetooth 6.0 channel ranging and lacks a multi-antenna design approach or official guidance...
