I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hello. We are evaluating the nRF9151 SiP as a potential solution due to its low power consumption and compact form factor . However, our team has limited experience with firmware...
Hi,
I'm considering the implementation options for nRF91 GPS front end. Having a shared antenna for LTE and GPS would be tempting, but I'm concerned about the filtering...
Hello,
I am trying to get some basic examples working with my new NRF9151DK and running into quite a few issues. Note that this is using a onomondo sim card that came with...
Hi,
With NCS v3.1.0 and Nordic's downstream zephyr ncs-v3.1.0, I got build failure with following message:
--
warning: attempt to assign the value 'n' to the undefined...
Hello Nordic team,
After many hours I have not been able to get socket dispatching working with Zephyrs MQTT client, and I am not sure how to proceed.
First of all I would...
Hi Support Team
Due to there is very little space of C: drive of computer, so I moved the NCS SDK from C: drive to D: drive. The VS code can't recognize the SDK and toolchain...
There are 100s of solutions on the zephyr git and the nordic git. It took me a while to understand it all and it took me hours of debugging and frustration before I ended...
I want to work with the nRF Connect Plugin for VS Code and my nRF52840 DK with Zephyr. I created a new application from the "nRF Connect" plugin and selected the hello world...
Hello,
I perform a test using a nrf52840 DK board in order to output a PWM at 50 Hz on a GPIO.
Here is the code:
void pwm_init(void) { nrf_drv_pwm_config_t const config0...
Dear Nordic-Support,
have a question regarding nrfutil and the offline package generation, described here: https://docs.nordicsemi.com/bundle/nrfutil/page/guides/installing...
I am evaluating Curve25519 performance on the nRF5340 and have observed that the following operations each require approximately 2.5 seconds to execute:
- `wc_curve25519_make_key...
My customer had ttothis question:
We recently purchased and use your Nordic Power Profiler PPK2 at my company. Does this device come with any calibration certificates? How...
Hi everybody,
I'm writing because I'd like to check if I understand the functionality of the AT command AT%XBANDLOCK correctly.
The first part of the question should...
Hi all,
I was busy extending the asset tracker project and all of a sudden I got this lte rejection. First I thought maybe it the data limit has reached on the conexa sim...
