I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
I am trying to run nRF9160: Azure IoT Hub — nRF Connect SDK 1.6.99 documentation (nordicsemi.com) on thingy91. I have followed Azure IoT Hub — nRF Connect SDK 1.6.99 documentation...
Hi,
I am looking at the product brief for nRF21540 and found "nRF21540 Development Kit" and "nRF21540 Evaluation Kit".
Where can I get the H/W information for them,...
Hi,
We want to implement a smart energy meter by using a mesh network including 200 nodes (nrf52840). What is your suggested protocol to do this?
Thank you in advance...
Hi! We're working on a BLE product which is intended for use in the US. This product uses an nRF52833 SOC, with some external components on a PCB we've designed with a printed...
I'm trying to evaluate a Nordic BLE module for a new battery powered project while waiting to establish a connection to a base station device. It seems like your lowest powered...
Hello,
When we tried to increase the Security level from SEC_OPEN to SEC_SIGNED_MITM, it will output error 0x6 which is "Not supported". So how can I do to support a higher...
We are developing AoA direction finding with nrf52833 and antenna array. We also want to include Wifi connectivity to our receiver, having nrf52833 + antenna array. Which...
Hello,
I want to perform NRF52840 Firmware update remotely. I refer to link .
I want only normal http OTA update without encryption for prototype testing. Is there any...
Hi, I've been measuring a nRF52840-powered prototype powered from a 3V coin cell battery. I would like to use High Voltage Mode with REG0 in DC/DC-mode for maximum battery...
Hi,
I am trying to implement the attribute reporting for a zigbee dimmable light device, reporting to the coordinator.
The code is based on the zigbee\light_control example...
MCU: nrf5340 Network Core nRF Connect SDK Version: 1.5.1 Currently there are multiple libraries under ncs/nrfxlib that have their own " nrf_errno.h" . Out of those libraries...
Hello,
i have a function wich just send "hello world" via uart0. static otError SendUARTCommand(void) { volatile uint32_t ret; const uint8_t message[] = "Hello World! \n...
Hi !
This is more of a question than an issue. I am curious about the future of TF-M and its implementation on Zephyr. Does anyone know what are the plans on Zephy's or...
I'm trying to set tx power to +3db in the peripheral_uart sample.
I don't need dynamic control, just setting to always use +3db.
Adding the following line to prj.conf...
Hi,
I am using coded BLE to connect two board using nrf52840. I just let bluetooth to run, then measure power consumption of the peripheral board by measuring the current...
