Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
Hi,
I have a working project and want to use I2C 2 instead of UART 2. I have changed the .dts file:
/* &uart2 { status = "okay"; current-speed = <115200>; tx-pin = <29...
Just wanted to share my project of controlling the position of feedback servo motor with Nrf52840 by sending bluetooth commands using nordic toolbox
github.com/.../Feedback...
I used the mpu6050 sensor and did it according to 1.2 of this blog .
The driver of this sensor is in the ncs\zephyr\drivers\sensor\mpu6050 directory.Error after compiling...
SDK: NCS 1.4.0
board: nRF9160-DK
sample: lwm2m_client
# registration CoAP packet
In option enum, there is no "others". Where can I get this information?
I'm writing an application that transmits data over a mesh network of nRF52840 microcontrollers using OpenThread. I'd like the microcontrollers to prioritize sending MLE traffic...
I want to upgrade my application from v1.4.2 to v.1.5.1. but the Bluetooth init failed. So I tested with the scan_adv, which uses the same logic as my application. This also...
The device communicates okay with JLINK commander v7.00a although at the beginning it always says "Connecting to J-Link via USB...Out of sync , resynchronizing... J-Link communication...
Development Environment: icore7 laptop running Ubuntu 20.04.2 LTS.
Target: To build connectedhomeip sample application for arduino nano 33 ble board and check against laptop...
Hi,
We are building our project with nRF52811 and Segger Studio V5.34. (I have Ubuntu 1804 if it helps.)
We have certain variable configurations but would like the ability...
Hello Team,
My end goal is to send 0 to 600hz signal over Ble using NRF52832[ as explained below image].
So, for this, I have used this GitHub code
https://github...
Hello,
I am working an a product based on the NRF52832 and I need to trigger an interrupt when a capacitive button is pressed / proximity detected (BLE is peripheral and...
Good morning,
I'm starting to develop an application for the nRF52805 using ble_app_hrs_freertos as a base.
The modification I did are:
Ported from nRF52832 to nRF52805...
Hi,
I am developing a beacon scanner on NORDIC Thingy 52 using Nordic thingy52 SDK, Now I want to add NUS(Nordic UART service) in my code to send data to the client(ESP32...
I have successfully built the Dynamic Multi-protocols network with Thread and BLE, and used Raspberry Pi 3B + as Gateway Now I want to integrate more AI into the system, but...
