Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
we are using D- and D+ in our nRf52833 board, I want to use the CDC ACM USB class as Virtual COM port.
I found that there has a demo example in the \examples\peripheral...
Hi,
We have a problem that occurs when
1) the GPS is at bootup of nrf91: indoor when we start the GPS search, and it doesn't find anything or maybe just 1 satellite...
Hi,
Looked through PS v1.3 didn't see any reference, so probably the answer to my question is no.
But can you please confirm that for me - does nRF52833 support boundary...
Hello,
I am doing tests on nRF9160 DK and I observe that if I send more than 1024 bytes on a TCP or UDP socket, the bandwidth drops.
Here are some numbers :
for...
Hi there
I mount the 19pin connector on nrf5340dk board and connect to segger j-trace pro . The debugger function work well.
Later i modify the nrf9160 etm trace project...
Has anyone had success getting triggers on motion to work with the LIS2DH? I only have INT1 wired so I modified the drivers to work on INT1 as the spec document says it should...
I'm writing software for nRF52832 using nRF5 SDK v17.0.2
I'm using a timer to create a buzz/tone using timer 3. This works as expected.
I'm also using the SAADC to measure...
I'm learning how to use OTA DFU (via BLE) now. I have Python 2 and 3, pip installed in my Win10 laptop. When I install the nrfutil with PowerShell, I had some errors (see...
I've been using the nrf connect toolchain for a bit, and after some initial trouble it was working ok, but now its randomly giving this error whenever I try to build anything...
Hi,
I am trying to convert a number from little endian to big endian. There is a built in function "NTON" that I can use instead of writing my own code, but I can not find...
I'm using two nRF52805 to get sensor values and send 2 sensor real-time values to my phone via BLE. Each nRF52805 BLE works well (Individually tested by nRF Connect App. It...
The encoders I am using generating about 500 pulses per second, and I need to read 3 of them at the same time. I assume a good approach for that is to use the hardware timer...
Hi, working with NCS v1.4.2, I see building products for an <app> landing into subfolder <app>/build/, in several flavours
app_moved_test_update.hex app_signed.hex app_test_update...
Hello,
I'm trying to flash an example code from the SDK onto the Arduino Nano 33 BLE board.
I tried to use the external debugging on an arduino nano 33 ble card but the...
