Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I have been trying to debug a curious behavior leading to higher energy consumption (~17mA) on my Sleepy End Device (Rx is off when idle).
I am using the nRF SDK...
I'm using nRF Connect v1.5.0 and Segger Embedded Studio (SES) to develop an application I'm testing on nRF5340-DK.
I want to create a "repeater" that has at least one...
When I use "Go" under debug, I get errors saying "No bootloader was found" and "ERROR 4 [NRF_ERROR_NO_MEM]".
However, when the same exact code is run on my friend's laptop...
Hi Nordic team,
I am having issues to connect to my Nordic device. The connection times out. By doing some research on the dev zone, it seems a known issue that could...
What is the fastest I can update information from the sensor to the nRF Cloud in terms of information every so many seconds?
This in reference to the asset_tracker file...
i have a custom NRF52832 board.
it have a 32mHz crystal but have not 32kHz crystal.
i use keil Uvision for programming, compile and burn the chip.
i use this example...
Hi,
I have been working with nrf5 sdk for my projects and now i am trying to port it into the nrfconnect sdk.
It looks a bit confusing and not able to find the proper...
I developed a custom pcb using the Raytac MDBT50Q-1M module. I tried to minimize the number of components added to the pcb by omitting the external 32K crystal oscillator...
Hi
I am using SDK v15.3 (nRF5_SDK_15.3.0_59ac345). I compiled and tested the MultiLink project.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hello,
I am tinkering with some BLE configurations specifically related to MTU and throughput optimization, and my question relates to using Notify on my attribute value...
Hi,
I am trying to change the state of a LED whenever there is a rising edge of a button
Here is my code :
When I build, I have this error :
By the way...
Hi,
I am using my nRF52832 with SDK v16 and Softdevice S132 v7.0.1.
My device has the Central role (and Peripheral) and connects to several devices which are added to...
Is it ever recommended to use a PA option in the LTE RF path? Specifically for cases where the device is very remote. For example, this option from Skyworks: www.skyworksinc...
Hi,
I started working on the nRF Asset Tracker. Was able to complete documentation till the Install the nRF Asset Tracker into your AWS account ( nordicsemiconductor.github...
Hello,
I'm wondering if there's a very low power way to detect a mobile network to connect to? Something similar to a carrier detect. Right now, my solution wakes up and...
