Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi,
I'm trying to incorporate pc-ble-driver-js into NodeJS based server.
For some reason, after connecting to a peripheral with a custom service, although the connection...
Hello
Trying to get the idea of whether the Long Range and Direction finding could be used simultaneously with the devices capable of both features.
Googling Long Range...
What causes the "Stopped by vector catch" error? Where is this documented?
The project builds successfully, but when launching the debugger, the Output window displays ...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I am evaluating nRF Connect SDK V1.5.0 for use on a new project. (I could use the added features since V1.2.0.)
Building with Segger Nordic Edition V5.34a
I updated the...
Using the sample code from this earlier devzone post , I've been trying establish communication with from my bosch sensor to my board. I have the code running: and it's printing...
Hi,
I'm combining a SAW filter with your nRF52840 and an RF MUX. The MUX requires AC coupling capacitors. Is that required in series with the SAFFB2G45MA0F0A as used on...
Are there software development tools/libraries for Mac/PC/IOS/Android for sending and receiving serial UART data to a nRF51822 module? I can run the nRF51822 and send and...
OS: Windows 10 64bit
SW: Segger Embedded Studio 5.10 nRF SDK 17.0.2 Softdevice S140
HW: nRF52833 2020.6
Hello,
I had found an example integrating the ble_app_uart...
Hey I'm currently trying to update the nrf9160DK_52840s bootloader through the nrf9160DK_9160 by which i mean:
-Send bootable image_52 over LTE or USB to 91
-Have a check...
Hi there,
We're in the evaluation of sending large payloads with nRF9160.
The payloads are 4-5MB in size which will come from an external flash chip.
The payloads...
Hello,
I try to upgrade my project from NRF5 SDK 15.3 to 17.0. I like to begin with the bootloader, therefore I followed the steps from
https://infocenter.nordicsemi.com...
Hi,
I'm playing 52832 ble_app_hrs_c Central example with latest SDK 17.0.2 and SD7.2.0.
The wierd thing is that after the service discovered, next enable cccd. But nrf_ble_gq_item_add...
I am using the nRF52-DK board to debug external board. So I am using the P19-Debug out cable.
And recently, I notice strange behavior as the on board nRF chip also get programmed...
On Nordic reference schematics the nRFxx symbols are designed with pins in all directions (up, down, left, right)
with the pin numbers 1,2,3.. placed in a 'PCB layout view...
