Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi,
We're running the aws_iot example and it would seem that by default it does not use the certificates in the file certificates.h
Is that the case and how can we use...
Hi,
I'm new to the whole Nordic environment, and I need to develop an application working with ble and lteM, so I have an nrf9160 DK for this purpose.
I worked with the...
I have a custom board based on NRF52811. Salient features:-
Both HF and LF crystals are present on board.
Power supply is 3.3V.
MCU DC-DC is enabled.
I am using...
Hello.
I trying the test for real time transfer a data.
Period is 4 ms and 5000 point data. (Total 20 sec)
The GPIOTE event occurs every 4ms and the processed...
how to unpair our nrf52 device once it's paired with another nrf52 device, currently we need to switch off the device so that we can pair another device.
Hi all,
I have a customer that has requested NRC tap to pair functionality for their device, mostly for convenience. This is fine, but I'd like to know what they're getting...
Hi,
We are running into a weird issue with some our devices when they are in the bootloader.
The bootloader fails with this error in nrf_dfu_validation.c: Invalid protocol...
Hello,
We have a firmware with 2 versions that runs on Baremetal and FreeRTOS on nRF52840 DK. We would like to port this firmware to nRF9160 without Zephyr and continue...
Dears.
when I connect nRF52833 to connect DK board, JLINK is ok .but could not find device from target device selection.
nRFGo studio is the same. what's the reason for...
Hi All,
I am able to perform the OTA DFU from the NRF52840 Dongle using the NRF Connect Bluetooth low energy application and default Nordic firmware.
I would like to...
I have a service with 2 characteristics, TX and RX. On TX the notify is enabled, because TX should send a notification when something changes. I manage to change what is needed...
Hello everyone.
We have a design based on NRF52840, which uses the built in USB peripheral and was fully tested and prototyped using NRF52840-QIAAD0-2031MR. We have now...
Hi There,
I have downloaded the nRFgo studio and nRFgo SDK and other files found here: https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF24-series
...
For the MPSL/timeslot example in NCS 1.5.0, I am trying set up a TIMER0 compare interrupt to take clean-up actions before the timeslot ends, as suggested in here . However...
