I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
I am trying to use the dongle as a sniffer. I followed the following instructions to download sniffer code onto the dongle:
#### nRF52840-Dongle (PCA10059)
1. Download...
Modify peripheral UART example to use a GPIO pin as 1-wire interface to read DS18B20 temperature sensor.
This modified code works for RBL BLE Nano v2.0 (nRF52832, nRF5 SDK...
Hi I am trying to get the ble_app_uart to run on my nRF52DK with the nRF52832 on board. I am using SDK version 16 and SoftDevice version 132. When compile and download the...
I'm trying to make a BLE app with nRF52832 DK, SDK v16.0.0, based on ble_app_hrs example.
After pairing on central device (smart phone), or CONNECT on nRF Connect app and...
Hi,
I am using the ble_app_uart as the basis for my project, where the NUS is used to send and receive data from my mobile app. The outgoing data is generated internally...
Hi, I am trying to run the periodic_adv sample on nrf9160dk_52840 which was added to the samples directory of the zepyhr repo 15 days ago. I am using nRF Connect SDK v1.4...
Hi Sir,
We have the " Capacitive sensor low-level library " as below in Nordic SDK.
1. err_code = nrf_drv_csense_init (&csense_config, csense_handler);
2. nrf_drv_csense_channels_enable...
Hi,
I use nRF52840 DK with SoftDevice 140 v.7.0.1 and SDK 16.0.0.
I want to get RSSI information (along with channel index) for BLE extended advertisements.
I enabled...
I am working with a custom hardware device similar to the Thingy91. I am communicating with an external device using COM1 using a binary stream at 38400 N81. (COM0 is assigned...
My design uses an RV-3028 RTC as an external 32 kHz oscillator for the application timer. Do I have to configure the SDK to use an external oscillator instead of a crystal...
I recently updated my multi-protocol (Thread FTD + BLE Peripheral Connectable) to use 'nRF5_SDK_for_Thread_and_Zigbee_3.0.0_d310e71'. I had been previously using 'nRF5_SDK_for_Thread_and_Zigbee_2...
Hi,
I setted up the LIBUARTE on my custom board...
NRF52833,SDK17.0.2,With Softdevice enabled
CODE:
-----------------------------------
NRF_LIBUARTE_ASYNC_DEFINE...
Hi,
I've found an issue while writing data to QSPI flash memory on the nrf52840 DK board with sample application.
The issue is that the data is overwritten to 0x0 address...
I am working on putting my NRF52840 to sleep with the RTC running (System ON WFE, not System Off). According to the datasheet, I should be able to call a soft reset and keep...
Hello, I am having some problems with what i assume is the readback protection. Is it possible to update the firmware of the device without deleting UIRC (serial number among...
