Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Is it possible to generate a DFU package for both bootloader-only and fully-programmed (bootloader, softdevice, and app) chips? I'm unable to do so for an nrf52833 using nrfutil...
Converting old code for a nRF51822 to the new SDK(15.3.0) for an nRF52832, this error happens:
#error "Compiler generates FPU instructions for a device without an FPU (check...
Hi all,
After wasting so much time trying to set up simple peripheral device whitelisting single central device, I realised that API has been updated and those old examples...
Hi all,
Can I read the chip ID of NRF24LE1 in code? how can I get the ID?
Or is there any readable identifier that make each chip "unique" from each other? Because the...
My team is developing a bike power meter, so we are looking to shrink our PCB design as much as possible. We are directly measuring force using an array of strain gauges....
I am trying to run the example of generating a random string from MBEDTLS website , below is my code , before running this code I have done the following changes.
Set MBEDTLS_CONFIG_FILE...
I have the problem to dfu nrf52833 over usb for a long time, I first have the problem cannot flash when start from a S140 BLE DFU example code, https://devzone.nordicsemi...
I am working on usb dfu for their one of the new chipset. but there is some issue, I keep trying different things and post on the ticket, but just no one responds. the sdk...
I have a feature request for the user_definitions.json file, which can be used to name custom services and characteristics in nRF Connect.
Any plans for adding more functionality...
Hi,
How can I develop my dongle to connect to devices with the name "device X", where X is a variable that can be 1,2,3,....
For example I want the dongle to connect...
Hello All,
I was interested in exploring the nRF52833 and didn't want to spend the money on a nRF52833 DK. Well I guess most of you can guess how that goes.
I purchased...
Dear All, I am trying to run a simple program that beacons, prints a message to the UART and toggles a pin on a custom nRF52833 based board. I am using softdevice s113 and...
my nrf51822 QFABC1 not working BLE , i used sdk 12.3.0 and uploaded softdevice is s130, and also I upload
I attached my schematics diagram also
please support any mistake...
Hi,
We are writing an application for nrf5340 similar to rpmsg sample with zephyr. We see that the application encounters stack overflow issue when flashed on target...
