Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi, I've began making a SPI module for programming a PIC16. It only transmits data, so two pins. My questions are: 1. any obvious errors? 2. does the EVENTS_ENDTX occur when...
Hello everyone
I have an question when I used the 52832.
First of all,I configed "nrf_drv_spi_init(&spi, &spi_config, spi_event_handler, NULL);" and the file (nrf_drv_spi...
We are about to use the nRF52832 and are looking at which SofDevice to select for a Central-only implementation. The S122 summary says it targets the nRF52820 and nRF52833...
i m using NRF52840 with sdk 15.2. In that i m testing direct test mode by UART.Now i can do transmit mode.i can check through nrfconnect dtm mode. i cannot check receiver...
Hi,
I tried the following AT settings on the nRF9160 DK board:
AT+CPSMS=1,,,"00111000","00011110"
AT+CFUN=1
After this the modem enters PSM mode and the current is...
Hi,
One of our modules using PCA10090 0.8.2 programming and production nRF9160/nRF52840 modules.
Our customer reported that they can't use PCA10090 0.9.0 re-programming...
Hi! I ran into a little misunderstanding in setting up clock frequency for PDM. I need to work with lower clock frequency than default - 0.64 MHz. I see, that PDM_CLK = 32...
Hi,
Some questions on the scan consumption of nRF52840 and using the attached Online Power Profiler for BLE as reference
If I am using my nRF52840 to scan 24hours at...
I wish to merge the cloud_client example with GPS example. How should I go about it? Along with main.c files of both, which other files will I need to merge?
I am currently making a program that will interpret serial commands from UARTE1 and then send + read something from the other (UARTE0). Previously, when I have been using...
Hello,
I want to be able to send 1 MB of data from a server node to a client node
I have made a simple model with an array that holds 300 bytes.
and upon a timer the...
Hi,
I want to connect Multi peripherals to one central and want to send the device name(peripheral which is connected) through the uart.
How do i get the device name which...
I have seen some variations of this issue but hoping someone can lead me in the right direction.
Similar to others, I am using NRF_LOG_INFO for debug messages. It works...
Hello, I am working on a project which uses nrf52832 module ( https://www.seeedstudio.com/MDBT42Q-nRF52832-based-BLE-module.html ). I just want someone to review its circuit...
