Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi,
I'm developping a new application where the device normally is in low power (waiting button with an interrupt)
while(!gIsButtonSwitched) { __WFE(); }
the consumption...
Hi everyone. I have an application using BLE and OpenThread dynamicaly. I am working with nRF52840 chip with nRF5 SDK for Thread and Zigbee v4.1.0 (Release Date: Week 18,...
Hello, I am using the Zigbee CLI Agent as coordinator, and when a router device or end device joins the network I want to configure attribute reporting.
I am able to configure...
We are running a trial in an open field, where we connect NRF52840 ( GW ) to an NRF 52833 (Node ).
Distance between the units is around 80 meter , we are using Coded Phy...
Hi Nordic team
I tried AWS FOTA and Nordic FOTA at nrf connect for cloud. It did work well.
We now want to set up our own cloud. It's neither AWS cloud nor nrf connect...
Hi,
Sorry for the newbie question but how am I going to use the SAADC to measure 4-20mA current loops? I've used the SAADC to measure temperature, voltage, and resistance...
Hello !!
We are using nRF52833 MCU in our one of project. It is very cost sensitive project. We are proving supply to MCU from coin cell CR2032 battery. Also we enabled...
Hi,
I'm currently developing custom board with nRF52832 and I'm experiencing weird issues.
It's mostly related to BLE, especially on Samsung A series devices (A3, A7,...
I am using custom board nRF52820. I'd done OTA up-gradation with USB connected. Firmware successfully updated on device over BLE and device got soft reset.
After removal...
I am using nRF9160 DK(PCA10090 0.9.0 2019.19) with Indian carrier LTE-M SIM and carried below steps to establish LTE-M communication with nRF Cloud: 1. Upgraded to latest...
Dear community,
I opened and successfully tried out the preflash_example. Since I will need a plain text NDEF message instead of an URI NDEF message as used in the example...
Hello,
I'm new to BLE and have a general question about concurrency and collisions. Sorry if a repeat question. I'm developing for nRF52832 using SDK 15.3 and S112 v6.1...
Hello,
I am testing nRF52 UART with DSP.
While transmit data in nRF52 (ADC results)
(example link: https://github.com/NordicPlayground/nRF52-ADC-examples )
I can show...
Hi
I am now working on a project which I use ble_app_uart_c as a reference.
SDK 16 and used softdevice s140.
The radio_tx_carrier() function was taken from example/peripheral...
