Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Dear dev community,
I've got a very simple question: How can I see the subscription and publishing addresses list in any mesh node for any model?
Thank you!
Regards...
Hi I am developing a custom PCB for the nrf51822 chip. I heard the nrf51822 chips do not come with preloaded firmware or bootloader. Do I need to also flash the bootloader...
Base on nRF5_SDK_15.3.0_59ac345 for NRF52810, I wrote the following codes,
Use nrf_drv_uart_tx to send data is successful, and NRF_DRV_UART_EVT_TX_DONE occur normally...
Hi All,
I am interested in designing my own Bluetooth beacon (Several of them, about 10) and connect it to a computer and read sensor data from those beacons (For example...
Dear Nordic:
Hi,i install nRF Studio <nrfgostudio_win-64_1.21.2_installer.msi>, and i want to erase NRF52840 flash,but when i click on "nRF5x_Programming",i cannot get...
Hi guys! I feel really excited about working with Nordic Semiconductors, but I have a problem with PWM driver.
Do you know how to support 13 independent devices that will...
Hello,
I was looking into the nRF5280 and was going to purchase it. But I had some questions that were not cleared up in the data sheets. It seems that a battery or a power...
Hello Everyone,
I have been using nrf52840 DK for several weeks. However I find it very difficult to understand the source code. I have experience only using arduino programming...
I've been attempting to use PSM but got an error.
I've already checked the post below. I download the project file and fixed a bit.
https://devzone.nordicsemi.com/nordic...
Hello .
I am looking for a way to pass the calendar time from the PC by the emulator to the MCU on first run.
I am using Segger Embedded studio 4.12
Is there a function...
I get the following error when launching the app, and the "Start scan" button either doesn't do anything or can't be clicked.
Error while probing devices: Error occured...
Hi
I am measuring the current consumption (with an amperemeter) of the nRF52 on the PCA10056 Devboard. The nRF52840 is supplied directly by connecting the external power...
Hi,
I have a problem when I do a write request on a 20 bytes characteristic from a custom service.
The funtion sd_ble_gattc_write return error 0x7 but I can't find what...
I want to stream a mono audio signal with high bandwidth (20kHz) from a remote device to a base device.
Need to A2D signal on remote and D2A the signal on the base. Low...
