Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I'm attempting to get Eclipse and the GNU Arm toolchain installed on my Windows 10 system. I'm following the instructions at...
https://devzone.nordicsemi.com/tutorials...
Hi All
I am a newbie with the nRF52 series SoC's and my end goal is to make a solar powered weather station.
I have a very crude nRF52832 dev board that I program with...
Hi, team.
There is a connection nfr52840 and esp32 (115200, 8, no parity, flow disable).
I'm using UARTE in interrupt mode (to send AT command and receive responses)....
Hi there, I am using the MDBT50Q-1MV2 Raytac module, with the nRF52840, and i have noticed that I have a very noisy VDD supply pin. Which definitely a problem because measures...
The qspi driver seems to make a number of assumptions about the protocol that don't fit the Winbond W25M02GW (and certain other) SPI flash chips.
Two major issues I've run...
I'm developing on an nRF52832 that has a serial connection with an iMX6 that is running a Python script with pySerial. For a while I had flow control disabled and would get...
hi i want to build a system with 500 device they send some data to controller wireless how can i do it with blu mesh ?
which chip should i select ? i prefer nrf52832
and...
nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730
nRF52840 Prewiew develpoment kit
I try to merge thread dfu client with simple coap server. there is error which i cant...
Hi! So I'm trying to use the throughput example with the nRF51422 board. infocenter.nordicsemi.com says that the SDK 12.3.0 throughput example will work with S130, which will...
Hi,
I want to interface sensor which has minimum requirement of UART supporting baudrate 921600 or SPI guaranteed maximum communication speed : 20 MHZ(Measured at 5cm...
Zigbee OTA upgrade example uses the Zigbee OTA cluster recommendations concerning the firmware file name (that is used for the version control and prevention of the downgrade...
Hi all,
We have custom board which has On Board Jlink support with nRF52832 using STM32 chip(STM32F072CBT6).
We are able to flash and debug using the On Board Jlink. ...
Hi there,
I was hoping someone could help me out. I recently got a hold of the nRF5 SDK for Mesh v2.0.1, and had a play around with the light switch example. I modified...
