Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
hi
I mistakenly left the inductor connected between the dcc pin and the DEC 4 pin and let it operate in the LDO mode.
What kind of problem will you encounter?
Or maybe...
hi all, I want to learn about HCI layer . It has 4 packet and I dont understand about HCI ACL data packet and HCI synchronous data packet . how are they diffent? Packet from...
-Dear Nordic Devteam
Thanks for your endeavor for the nRF Sniffer 2 . Although it is a beta version, this is sincerely anticipating.
To set up the Sniffer you will...
I am developing some firmware using SDK 8.1 where power consumption is absolutely critical. The firmware will make a ble connection between the central and peripheral device...
I'm facing a strange problem that I don't really understand:
I'm using 51822 (s130) on a custom board to communicate with iPhone 5S. The parameter that is able to establish...
In multi-link central app, after BLE_GAP_EVT_CONNECTED event, BLE_LBS_C_EVT_DISCOVERY_COMPLETE is called NRF_SDH_BLE_CENTRAL_LINK_COUNT number of times.
So For example...
Hi,
I use the original "nRF5_SDK_14.2\examples\ble_peripheral\ble_app_uart" no any modification, in Keil the .hex file size is 71k while it is 153k in SES.
My questions...
I am working on SDK V10.0.0 because I need S310 softdevice.
I like SEGGER_RTT I used in SDK V11 and V12.
But I got the Error in the subject line.
I had to uncheck use_microlib...
Hi,
I build below sample in SES and receive an error for:
Compiling ‘nrf_log_backend_serial.c’
can't open '...nRF5_SDK_14.2.0_17b948a/examples/ble_central_and_peripheral...
Hi!
There are many questions about flash memory already.
But I could not find the question I wanted.
I want to save scan data to flash memory.
However, when you...
As a peripheral,S130 can work ok,but when I add a central role, there is a error at central start to connect a peripheral. err_code = sd_ble_gap_connect(&addr,&m_scan_param...
When a peripheral advertises on one of the three advertising channels, does it listen for a short duration on that channel (as implemented by the Softdevice?) And then repeat...
Hello.
I am measuring the current of nRF52832 using Power Profiler Kit(PPK).
I used the following case with PPK setting.
infocenter.nordicsemi.com/index.jsp
At...
Hello Folks,
I am using PCA 10056 Eval board. I am using SPIM0 to connect 5 slave sensors. The Chip select is done by the UART Tx pin. So If I send 0x01 over UARt then...
