Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
quick-stop_2_with_soft_filter_NRF52_DK (1).hex I imagine that my question is just one from lack of experience. I apologize for that but I cannot find any information on the...
Hi!
I would like to use long button press to send device into sleep mode (using BSP module). Since button is tied to ground, when device goes to sleep mode, and when I...
I need to us an external RF amplifier that requires TX and RX control lines. I'm looking for a way to tell when TX starts to kick the unit into TX mode. I also need to know...
Hi,
We use NRF52832-based BLE module running serialization (SDK 14, softdevice 5.0.0) and STM32F407 MCU running application firmware on a custom board. The project is created...
Hello!
I am looking examples for nRF5_SDK_14.1.0 (For example - ble_app_eddystone )
I need read all attributes with ATT_Read_Blob_Req command.
I can read Device Name (0x2A00...
Hello,
I am using nrf 52832 and sdk 14.0.0. and i am using "ble_app_uart".
I am developing an iOS application.
Its purpose is character transfer.
I want to transfer...
Hello,
I did a quick test using 2 nRF52840 kits to measure the change of the RSSI value based on the distance and the used PHY layer.
For each test, I configured both...
I was reading through the documentation and it mentions you need;
One PCA10028 or PCA10040 development board for the client.
Three development boards or dongles...
Hi,
Is anyone successfully using MMD with the nRF52840 PVK, SES 3.3, recent SDK (e.g., 14.1.0) and S140 softdevice?
I followed the steps in this blog post both on Win10x64...
Hi.
Our company is designing a new device using the nrf52832 chip for BLE communication with other equipment from our Company.
Does the chip come with a factory preprogrammed...
Hi
We are developing ble peripheral application for the nrf52832 using SDK v13.0.0. and everything was working correctly until we tried ble connection with the iphone 7...
Hello Sir,
I have developed my application using nRF52832 chip with BLE connectivity. My device is battery operated and hence i am looking for WiFi chip with small size...
I have three questions about using AES CCM encryption by S132 timeslot API.
Is there an example value for the time request parameter in sd_radio_request(), when using...
I'm working with uart on the nrf52832 and I'm facing an issue related to the baudrate.
In this post a formula for calculating the baudrate given the register value is given...
I'm setting up the message structure for usage in a sensor Model. The sensor readings may be represented by different data types (e.g. float, integer). How is this best handled...
