Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi,
I've couple of Nordic Thingy 52.
I was able to connect to these using my Samsung A5 2017 running Marshmallow and see the various sensor readings.
After an OS update...
I am in the process of porting my code from SDK13.0 to 14.0 in order to use s332 v5.0
I can compile and run my application. While it's running, I can see that it is sending...
We are using this device and we seem to have an issue reading from P0.20.
I know this is a dual purpose pin. We have programmed it for input with pullup. We have it attached...
I am currently porting my project from SDK13.0 to 14.0 so I can use s332 v5.0.0.
I receive warnings when compiling
.\_build\nrf52_firmware.axf: Warning: L6330W: Undefined...
I would like to know if it's possible to pair two NRF52832 together using NFC. NOT an android phone to an NRF52, but a central NRF52 standalone connect to a peripheral NRF52...
Hello,
I am using nrf52832 with SDK12 with gcc compiler. I have extended the ble_app_template example with 2 services.
I have 1 timer interrupt using RTC(100 ms) and...
I've been noticing lately when running debugging on my code, a few minutes in it loses connection and says No Source Available for "0x01e054". I'm sure how to even figure...
I am trying to debug a custom version of the bootloader_secure_ble example but am running into FLASH space issues. The bootloader app does not fit into FLASH with -Og optimization...
Hello,
I am using Keil IDE for a while,and it is working perfect so far until, my code size gets bigger than 32K, I also decided to try GCC. I noticed GCC code size for identical...
nRF52832
SDK14.0
Hi,
I had two questions regarding Fstorage:
The Fstorage module works by having a queue of NVM operations. This queue only holds two types...
Hello!
I am using the nRF52832 with nRF5_SDK 14.0.0. with a JLink connection. My OS is Ubuntu 16.04.
After placing NRF_LOG_INFO() statements around my code, connecting...
Hi,
I am working on an application that needs to use pairing/bonding. I am incorporating peer manager into the project. I have included in Makefile paths the following...
I'm a little confused here...I have a basic main function which is turning on/off some GPIO and logging through SEGGER_RTT.
I thought that in order for that to work, you...
Hi,
I'm trying to get SPI working with an accelerometer (LIS3DH). I'm currently trying to use the nrf_drv_spi_transfer() function. See code snippets below.
// Initialize...
SDK14.0.0
nRF52832
s132
I would like to DFU the contents of the App Data section. In particular, I would like to erase the contents for a "factory reset" command.
...
