Hi, last year the name of the Zephyr module "TraceRecorderSource" was changed to "percepio". In January a PR was accepted that updated the SDK's allow-list (west.yml).
We...
Four returned products after sale could not be turned on & charged normally. Preliminary analysis of disassembly showed that the MCU was damaged, and the MCU was cross-verified...
hi support team,
may i ask do we have demo on how to test remote provision in ncs2.9.0?
i assume there are two possiblilities:
1.
For server, we need add below settings...
Hello,
We are using a BLE module based on nRF52832 with a U.FL connector for external antenna connection. One of our automated tests requires we turn off/on the antenna...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
Hi
We are using the CMakePresets.json file for different variations of our firmware. Since the latest update (2025.4.106) the build configuration interface changed a bit...
Hello.
I am trying to build project for thingy52 but since latest release of sdk for thingy does not work well with SES -> https://devzone.nordicsemi.com/f/nordic-q-a/27311...
I am trying to interface BMI160 Shuttle Board to the nRF52840 Development Kit using TWI interface. I am using IAR Systems IDE and have modified the "twi_sensor" Example code...
Hi,
I am using ncs V1.0.0
When I configure P0.5 as input it takes 37uA current. (Interface with PCA63548 / LIS2DH Interrupt)
If I not configure the pin as input getting...
Hello .
We have an issue with the SPI channel.
We found out that when our GPIO config as SPI the CS drawn a lot of current when it connect to the slave device device AD7770...
Hello,
I am working on pc-ble-driver-py to design a central (using a DevKit with a nRF52832). At this point I am trying to perform a phy update procedure but I see it is...
Hi Everyone,
I am using PSM mode in my program and want to send data everytime when modem wakes up from sleep(PSM mode). I also want to turn off/on UART only when required...
Hi,
During startup the nRF sniffer extcap script does the following:
Which (at least on Linux) breaks applications having open serial ports.
Why not instead use...
Hi all,
I have mqtt sample on my board, after I added MCUboot module from Configure nrf Connect SDK Project, when I try to debug, it gets stucked at :
#elif defined(CONFIG_ARMV7_M_ARMV8_M_MAINLINE...
hi,
nrf52840 BGA footprint P0.22 config as UART0 RX mode, don't receive any data, but config as other pin P1.06, work normally.
and I also test QFN footprint with nrf52840...
I have nrf52832 platform and my version of softDrive is (nRF5_SDK_15.3.0_59ac345). I red a lot of documents and tech support like these links but couldn't find my problem...
I have another MCU on the same board as the Nordic 52832. The firmware update image for the MCU is about 50kb in size, so instead of adding a parallel DFU for the MCU through...
So currently I am using a 5 second repeated timer to run all my operations but there is a draw back to this that the max accuracy I can achieve is of 5 sec, like if I want...
Hello!
I have 18-bit sensors with SPI and I2C , which I intend to use in a wireless array.
I need to choose equipment and topology (star, scanning mode?), enabling data...
We had a custom board made with the nrf9160 and I noticed I was having trouble communicating with the sim card on my board.
We have been testing i2c, spi, number of peripherals...
