Good morning,
In my application (SDK v 2.8.0) I would like to disable/enable runtime the advertising for the mesh provisioning. The inizialization of the mesh stack works...
Hi,
Our project need 7 seperate PWM outputs, as the nRF52840 have 4 hardware pwm, I decide to use GPIOTE with PPI to create extra 3 pwm outputs to drive Red/Green/Blue...
Hi, last year the name of the Zephyr module "TraceRecorderSource" was changed to "percepio". In January a PR was accepted that updated the SDK's allow-list (west.yml).
We...
Four returned products after sale could not be turned on & charged normally. Preliminary analysis of disassembly showed that the MCU was damaged, and the MCU was cross-verified...
hi support team,
may i ask do we have demo on how to test remote provision in ncs2.9.0?
i assume there are two possiblilities:
1.
For server, we need add below settings...
Hello,
We are using a BLE module based on nRF52832 with a U.FL connector for external antenna connection. One of our automated tests requires we turn off/on the antenna...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
hi..I have merged the saadc with ble_app_uart and i have added all the respective files and enabled the ppi, saadc everything . while i am running the code ,getting unknown...
Hi,
I noticed something strange while developing with the nRF9160 modem's RTC. Here's the sequence of events
Connect cellular
Get time from NTP server and initialize...
Hello nordic
I'm running iot icmp example on my nrf52832.
The border router is Rapberry 4. root@raspberrypi:/home/pi# uname -a Linux raspberrypi 4.19.71-rt24-v7l+ #2 SMP...
Hi Nordic Support,
I am not getting sensor(VL53l0X) value,i used slave device address=0x29 and register address=0x01. I am getting starting distance value=255,afterwards...
Hello ,
I am trying to send 1,000 of MPU-9250 data from NRF5832 peripheral(ble_nus_uart) to NRF52832 central(ble_app_uart_c).
And i have been searched this site and...
Hello, I'm working on a project that contains 2 small enclosures each with a sRF905 and processor that monitors temp and humidity. One of the enclosures is mounted in the...
Hi, Last week we received Nordic's Thingy:91 development kit and prototyping platform for nRF9160.
The kit also included 1x iBasis SIM card. According to iBasis, LTE-M is...
Hello,
i'm using,BMD-301(NRF52832),SDK15.3.0
////////////////////////.......Issue-1..............
When i upload "twi_master_using_nrf_twi_mngr" peripheral example...
Hi, I'm developing a Zigbee coordinator starting from CLI agent example on nRF5_SDK_for_Thread_and_Zigbee_v3.2.0_9fade31. The end node I tried to connect is Ikea TRADFRI ambience...
I2s subcontract transmission, the sound is normal during the transmission of each packet, and there is noise when preparing next_buf. How to eliminate the noise? Looking forward...
Hello Community,
I want to request a timeslot with sd_radio_session_open(). Whenever i call this API function, the Application crashes with a HardFault.
I have no idea...
Hi Devzone!
I'm using 'nRF52840' as an edge device, and this device is going to continuously check the surrounding environment and send the value to mqtt broker of aws through...
Hi,
We are using nRF52832 with a custom protocol communication (not BLE, not Nordic). The communication is simple, one device is sending message and the other is receiving...
Once again I'm turning to this forum for help, as I'm stuck with an unusual issue. We have a custom board, which is supplied from one CR2032 battery and can also be suplied...
