Hi, I am fighting with a bug I found in SDK v2.8.0 for BLE scan filter on a test project as follows: 2 Devices (Ezurio BL653-DVK using the nRF52833), both having central and...
During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hi,
We are trying to get the serial dfu example from sdk 14.2 working with an nrf52832. After flashing the device succesfully and starting up the bootloader we were unable...
Hello,
I recently switched to linux and I have many problems since then.. So I noticed that printf functions are not working fine for me e.g. in ble_peripheral_uart example...
I've worked with other integrated radio + ARM processors that were not deterministic, and I would like to know if the Nordic solution is.
What I mean is: Is there a way...
Hello all,
How does the handling of ble events work with SDK 15.1? When I register more than one event handler with the macro NRF_SDH_BLE_OBSERVER(), how does the softdevice...
Hello Support team,
I'm working on a project where I am designing a custom board uisng the Nordic NRF52840 as the MCU (forgive me if I'm using the incorrect terminology...
Hi,
I am relatively new to programming hardware at this level, and have developed our product on the 52832, so finally I have purchased the Power Profiler Kit, and downloaded...
Hello good morning,
I am using nrf52840 device. I am sending 20 bytes using notification at different notification intervals like 30ms, 80ms and 1sec. But at application...
hello
I am currently trying to use the thingy_52_sdk sample code to embed a program using the J-link debugger with the Nordic thingy 52 development kit. But the build is...
Hello,
I am attempting to test slew of Rigado BMD-350 module BLE radios (uses nRF52832) using a Rigado BMD-301 series Eval Kit to act as the central. The BMD-350 device...
Hello everyone, the sdk version that I use is 15.0 (nrF5_SDK_15.0.0). The soft device is s132. In the ble_peripheral / ble_app_uart example you can only connect through the...
If followed the following steps:
Installed Win10Pcap
Installed Wireshark-win64-2.63 on Windows 10.
Using nrfGo Studio loaded sniffer_pca10040_51296aa.hex (after erasing...
Hello fellow Nordic Community,
We have a usecase in which it would be beneficial with a tx power of - 30 dBm . This is a value that was supported with the nRF51 chip series...
Hi,
I am develop a project with dfu and bond features. I found that in dfu project, IS_SRVC_CHANGED_CHARACT_PRESENT is always set to 1. In my understanding, if set this to...
hi,
i am using Nordic thingy:52 with a nRF52840 with s140 softdevice to receive multiple characteristic data from thingy like thingy environment service have 6 characteristics...
Hi,
Is there any way to stop the OTA DFU? Let's say that I started it and at some point I want to cancel the process at 40%. Is there any way to send a control message to...
