Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi Nordic,
Could you please help me ! This is an urgent matter!
Based on this discussion , there is an error rate of actual baudrate comparing with the desired one.
...
Hello everyone,
I'm trying to use the new SDK 15.0.0 and the S140 soft device V6.0.0. I would like to use the LE CODED physical layer and set my TX output power, but when...
Why did the softdevice handler's API change?
sorry for a general question. I used SDK 13. and Now, I am porting my software to SDK 15. So, I have simple question. Why did...
My application is based of the UART example, I have a repeating app timer that fires every 5 min's to do some tasks, I also utilise single fire timers (initiated for events...
Ok, so I am using nRF52DK and trying to figure out to how to send up to 6 packets of data from custom service that sends 6 16bit values per packet. When I send one packet...
Hello,
We have a custom boards that powers a NRF52840 module from a 1.8v voltage regulator coming from a 3.6v battery. We also connected the positive pole of the battery...
I am new to embedded development. How do i physically connect the sensor to the board?
Is it possible without any additional equipment? What is important regarding pins...
Hi,
We want to certify a product embedded nRF51822 chip, with BAS and IAS defined by Bluetooth SIG.
Requesting SIG certification for it of a certification body, we were...
Hi all,
getting burnt out from searching the fourms and finding dead ends or outdated answers so just posting a question quickly.
Somewhere along the line my nrf51DK has...
I am working on a product based on the nRF52832 (using the Rigado BMD-300 module) which is basically a data logger with a BLE connection for offload. I am running FreeRTOS...
Hello,
We have a custom board based on nRF52832.
there is 1 LED on P0.29:
#define LED_1 29
First I initialize the GPIO:
nrf_gpio_cfg_output(LED_1); // this lights...
When I complie this SDK using keil5, I got this error "Error #544: Required Software Pack 'NordicSemiconductor.nRF_DeviceFamilyPack.8.16.0' is not installed'" How can I get...
red-contrib-nordic-thingy
Always getting "no thingy found" error from node-red in ubuntu. But i am able to use gatttool and able to get notifications from thingy on button...
I've noticed following line in SDK14.1 release notes:
`
Fixed a bug where nrf_log could crash when heavily loaded.
`
I'm using SDK13.1 in my current project...
I've recently jumped to nrf5 sdk v15.0 from v12.3 and met a problem in setting up a custom ble service. Actually the service itself is visible via nrfConnect andorid app,...
