Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi everyone,
I created a custom service that I want to be advertised through scan response. Also, I want to advertise the INFORMATION SERVICE through advertising data. I...
Hi, I'm working with nRF52840 with NFC. I don't have yet the external antenna to connect to (now I'm using uFL), but I'm not sure about the trace width that goes from the...
MeshSDK: 3.2.0
StockSDK: 15.2
Hello,
I have a network where the sequence numbers have become corrupt due to removing devices from a network and then provisioning other...
Hello,
I've been trying to write my own library that uses UART.
I went through the "uart" example and wrote this piece of code.
uart.c
gpio.c
main.c
...
I would like to ask you a question, that is, the RTC in the chip of 52832, in the case of non-power-off restart, is there any way to keep the RTC time and continue the timing...
I am trying to extract the gps coordinates and use CoAP to sent the info to Telenor IoT server. I am using the gps demo code provided by Nordic .
https://github.com/NordicPlayground...
Hello,
I want to program nRF5340 via UART.
What is the hardware related event that puts the application processor in program mode over the UART ?
All ARM microprocessors...
Hi
OS: Windows 10 (32-bit)
nRF Connect application: v3.3.1
Getting started assistant: v3.3.1
Please see the attachment. After installing ninja, tried to verify it...
I`m searching after an application document / description of a test setup, how to measure BLE data throughput with our product including nRF52840. Maybe Nordic have a smart...
I've been programming in SES for several months now, and I need to put the code into libraries to keep an overview of my project.
I've been able to include SDK libraries...
hi, I used NRF52833 to debug the program, and I used the ble_app_hid_mouse project in SDK16 to debug the fstore function ,and the file path is E:\nrf52833\nRF5SDK160098a08e2...
Hi everyone,
This is my first time using Nordic nRF SDK, so i hope that I'm not asking for anything too stupid, I'm having troubles in adding nrf_logger.h into a project...
I've noticed that the BT-SIG listings for s132 v6.1.x https://launchstudio.bluetooth.com/ListingDetails/64933
and s140 v6.1.x https://launchstudio.bluetooth.com/ListingDetails...
Hello everyone!
We are developing a device with the nRF52840 SoC and using mbed-os for developing firmware.
Everything works and runs normally when using mbed softdevice...
