I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I wonder if there is any way to program DK without physically owning it. Is there is any kind of simulator? Namely, we are in the process of developing for one startup, so...
nRF52832, SDK15, s132
When I have event PM_EVT_BONDED_PEER_CONNECTED, should I call
for secure connection? Or it secure connect will call automaticly from SD? Because...
Application Summary: My application is a mesh node that also implements a BLE central (to periodically connect to a BLE peripheral) and acts as a mesh relay with custom mesh...
Hello,
I'm trying to get an idea of the level of security provided by various security features described in the nRF52840 specification and several of the application notes...
Hi!
I'm currently setting up the nRF9160 dev kit for development and are having some trouble with "building" the asset tracking application.
Building ‘zephyr/include...
Hi All,
I am doing a Mesh development project with nRF52840 and a custom board. SDK version: nrf5SDKforMeshv320 Testing Example: light_switch
I had changed the port/pin...
The goal is that we can update the firmware version with the smartphone or tablet without having
need to go through the development tools
(cable, IDE, ...)
if so, how can...
Hi,
In our firmware we're writing the entire contents of our UPDATE.BIN file successfully with flash_img_buffered_write's, but after boot_request_upgrade and a sys_reboot...
When my Nordic device is running my custom BLE application I notice that the device address is 0xC4318DBD687C. When device is running the bootloader service the device address...
Hi Nordic,
As far as I can see, there is BLE_NUS_CONFIG_LOG_ENABLED defined for ble_nus in sdk_config.h. However, I cannot find the similar BLE_NUS_C_CONFIG_LOG_ENABLED...
Hi, can we use a manufacturer name of our own for the usb in nrf52840?
We know that we can still use the Nordic Semiconductor's usb vendor in a commercial product.
Best...
Hi, Can I use nRF24LE1-F16Q24-DK without nRFgo Starter Kit? If yes please suggest me programmer to program nRF24LE1 by Keil IDE. by referring documentation I found its support...
Hi
SDK v15.2.0 SD 6.1.1
I have managed to send out "Connectable, Non-Scannable" extended adverts with some AD packets as payload. On a frontline sniffer as per the file...
I am developing a HID keyboard based on an nRF51822.
The firmware source available here:
https://github.com/martonmiklos/ble_keyboard_fw
(It is based on the ble_sdk_app_hids_mouse...
