Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
According the documentation , the msb 16 bit should identify the module, so why do I get 0000 here?
0xCA appears to be the module code for the nrf tls interface, as it's...
Hello,
I am using the NRF52-DK softdevice 6.0.0 and NRF SDK 15.0.The app is based on on the saadc PCA10040 S112. I want to add static const nrf_drv_timer_t m_timer = NRF_DRV_TIMER_INSTANCE...
Hello I am in a development stage
1. MBN52832 soc
2. s132 softdevice
3. nRF5 SDK v15.2.0
4. SPI PHY
So my concern is I want to port serialization library for SPI...
Hi, I hope it is fine to post a question like this since I'm not familiar with the license/copyright issues.
I have a friend of mine who wants to post BLE lectures using...
Hi, all.
I m trying to combine two example spi + timer using nRF52832.
But spi_event_handler function in the ex spi and timer event in the ex timer are crashed.
...
hi,
how can i scan for other BLE advertisments on nrf52811? there is no official documentation showing how to have Central role on nrf52811 softdevices! and no support in...
Can I still use the USB while the nRF9160DK is set up for current measurement as described in the spec, where power is applied on P28 after cutting solder bridge SB43 and...
I am using PCA10090, version with active GPS (tested using GPS sample)
I tried configuring using:
vi /nrf_root/ncs/nrf/applications/asset_tracker/build_nrf9160_pca10090ns...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
According to this thread, GPS sensitivity of Thingy:91 does not seem to be good while I haven't tested this yet.
https://devzone.nordicsemi.com/f/nordic-q-a/51424/thingy91...
Hello.
I have found this document and have a question.
In according with document below: service " Generic Access" (UUID1800) has a few characteristics: " Device Name...
We're attempting to get a Bluetooth data stream set up on our nRF52840. We've taken Zephyr's peripheral sample and pared it down somewhat to only allow indications from the...
Hello,
I am working on LPN node code from the mesh SDK 3.2.0. When I run the example code, I see a current peak at every 2 sec interval. Please check the image attached...
