Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
Is there a possibility that the order of the responses can be different with respect to the order of the requests?
We check for the success status of the APIs sd_ble_gattc_read...
These two options in nrf_mesh_config_app are arbitrary for me if I don't understand how they should be sized.
From the documentation of the MESH SDK 3.2.0:
ACCESS_FLASH_PAGE_COUNT...
My app runs the following code, that is supposed to init the SoftDevice:
nrf_clock_lf_cfg_t clock_lf_cfg = { .source = NRF_CLOCK_LF_SRC_XTAL, .xtal_accuracy = NRF_CLOCK_LF_XTAL_ACCURACY_20_PPM...
Dear Nordic,
We have developed a product utilized the NFC readable/writable feature of NRF52832. We have tested it against some of the HTC, Sony, Samsung, and Google phones...
Hi,
I will add feature "installation codes".
I guess that security API do work.
At coordinator side, zb_secur_ic_add, zb_set_installcode_policy functions
At end device...
I am trying to implement nRF52 Light Switch Proxy Server in nRF52832 boards. Everything works fine on behalf of board and it prints the Device UUID as well. Although I can...
i'm using nRF mesh sdk v2.1.1 with 2 boards and 1 provisioner board. I have un-provisioned 1 board with the help of config_client_node_reset(). I want to know the procedure...
Hi,
In your Light switch example, there is a GPIOTE_IRQHandler() in simple_hal.c. Since I added the nrfx_gpiote module to the project, this is conflicting with the nrfx_gpiote_irq_handler...
Dear：
I used the nrf9160DK version to 0.8.2, updated the latest firmware mfwnrf9160100, using the NBIOT SIM card, and using the SDK version as nRF Connect SDK V1.0.0. After...
Hi there,
I'm developing applications with nRF52840, SoftDevice 6.1.1. Normally the scan timeout is in step of 10 ms. But whichever the value I set between seconds, e.g...
I am currently trying to combine the TWI_scanner and UART examples from PCA10028 into one example program. I am copying over code from one main.c file into the other.
So...
Hello, I'm working on a project where I want to send data through notifications between nrf52832 custom ble service server to the hrs_c example client. I'm using s132. When...
Hello,
I made my nRF52840DK go to sleep.
It was immediately restarting.
RESETREAS and LATCH gave me the cause of the reset and I fixed it.
Now, I can put it to sleep...
Hello,
I get the same massage in the nRF toolbox app when tring to connect to both HRM and the UART examples.
I upload the hex file as written(did the same thing with...
Hi
I have the nRF52 DK and I have an external nRF52832. I know how to program the external nRF52832 using via the nRF52 DK using SEGGER Embedded Studio.
But I wonder...
