I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
As regards the NRF52840, I want to make sure that it is in System Off not Emulated System Off. Hence the device must not be in Debug Interface mode .
I want to retain the...
We're developing a low power communication stack, where every uA counts.
Currently, I have the system running at a few uA higher than expected, which I'm trying to track...
Hi,
We are developping an app using nrf52840. We started with the SDK14.2 and needed to migrate to SDK15.0 in order to use the long range. We are also using a Bootloader...
hi,
i am trying to on/off led on board(light_bulb code) which is controlled by the other board(light_switch code) with a gpio. when gpio is high led should be on and when...
I am using a NRF52832 and i want to burn a HEX bootloader that only jumps to my APP (i have already burned the Softdevice) when i reset it...
Can you help me ?
Hi,
I am trying to get the GPS from my thingy91, but it is not working. I can see that the board has CAT-M1 connection when I press the top button to get the GPS signal...
Hello!
I am trying to upload my compiled code via nRF Connect v2.6.2 to my nRF52832. But in nRF and also in J-Link RTT Viewer v6.46d it doesn't seem to connect properly...
Hello, I'm developing a BLE peripheral + Zigbee Coordinator, starting from ble_zigbee_dynamic_template of nRF5 SDK for Thread and Zigbee v3.1.0. Both applications (BLE and...
Hi,
After using the ibasis data available on the sim card:
- what is the cost per MB of data consumed on the ibasis provider, please ?
- After using the data available...
Hi, I'm trying to implement UART interface with HW flow control on nRF52832. After some investigation I found libUARTE is the most advanced option.
During testing I found...
We are trying to update the BLE Advertisement using ble_advertising_advdata_update, the function seems to always return 0x3200 and ble_gap.h:178 tells me its a BLE_ERROR_GAP_UUID_LIST_MISMATCH...
Hi I am using a NRF52-DK BLE/NFC
I want to check to see whether I can use the soft Device 132 API, Device Download package and whether it is applicable to me as I want to...
Hi,
I am having difficulty changing the UART Tx/Rx pins of nrf52840 (custom board) in the direct_test_mode example project in the SDK 16.0.0.
Based on https://infocenter...
